Bedienungsanleitung Makita JV0600X1 (Seite 7 von 13) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

711076

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

CAUTION:

• The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing saw blade (Fig. 4 & 5)

CAUTION:

• Always clean out all chips or foreign matter adhering to

the blade and/or blade holder. Failure to do so may

cause insufficient tightening of the blade, resulting in a

serious personal injury.

• Do not touch the blade or the workpiece immediately

after operation; they may be extremely hot and could

burn your skin.

• Use only B type blades. Using blades other than B type

blades causes insufficient tightening of the blade,

resulting in a serious personal injury.

• When you remove the saw blade, be careful not to hurt

your fingers with the top of the blade or the tips of work-

piece.

Before installing the blade, make sure that the blade

clamp lever is in the released position.

To install the blade, insert the blade (teeth facing forward)

into the blade holder until it latches. The lever moves to

the fixed position by itself and the blade is locked. Pull

the blade lightly to make sure that the blade does not fall

off during operation.

CAUTION:

• If the lever does not move to the fixed position by itself,

the blade is not installed completely. Do not press the

lever by hand to the fixed position. It may damage the

tool. Make sure that the back edge of the blade fits into

the roller.

To remove the blade, push the lever forward as far as it

will go. This allows the blade to be released.

Hex wrench storage (Fig. 6)

When not in use, store the hex wrench as shown in the

figure to keep it from being lost.

OPERATION

CAUTION:

• Always hold the base flush with the workpiece. Failure

to do so may cause blade breakage, resulting in a seri-

ous injury.

• Advance the tool very slowly when cutting curves or

scrolling. Forcing the tool may cause a slanted cutting

surface and blade breakage.

• Hold the tool firmly with one hand on the main handle

when performing the tool. If necessary, the front part of

the tool may be supported by the other hand.

Turn the tool on without the blade making any contact

and wait until the blade attains full speed. (Fig. 7)

Then rest the base flat on the workpiece and gently move

the tool forward along the previously marked cutting line.

Bevel cutting (Fig. 8, 9 & 10)

CAUTION:

• Always be sure that the tool is switched off and

unplugged before tilting the tool base.

With the base tilted, you can make bevel cuts at any

angle between 0° and 45° (left or right).

Loosen the bolt on the back of the base with the hex

wrench. Move the base so that the bolt is positioned in

the center of the cross-shaped slot in the base.

Tilt the base until the desired bevel angle is obtained.

The edge of the housing indicates the bevel angle by

graduations. Then tighten the bolt to secure the base.

Front flush cuts (Fig. 11)

Loosen the bolt on the back of the tool base with the hex

wrench, and slide the base all the way back. Then tighten

the bolt to secure the tool base.

Cutouts

Cutouts can be made with either of two methods A or B.

A) Boring a starting hole

For internal cutouts without a lead-in cut from an

edge, pre-drill a starting hole 12 mm or more in diam-

eter. Insert the blade into this hole to start your cut.

(Fig. 12)

B) Plunge cutting

You need not bore a starting hole or make a lead-in

cut if you carefully do as follows.

1. Tilt the tool up on the front edge of the base with

the blade point positioned just above the work-

piece surface. (Fig. 13)

2. Apply pressure to the tool so that the front edge of

the base will not move when you switch on the tool

and gently lower the back end of the tool slowly.

3. As the blade pierces the workpiece, slowly lower

the base of the tool down onto the workpiece sur-

face.

4. Complete the cut in the normal manner.

Finishing edges (Fig. 14)

To trim edges or make dimensional adjustments, run the

blade lightly along the cut edges.

Metal cutting

Always use a suitable coolant (cutting oil) when cutting

metal. Failure to do so will cause significant blade wear.

The underside of the workpiece can be greased instead

of using a coolant.

Dust extraction (Fig. 15)

Clean cutting operations can be performed by connect-

ing this tool to a Makita vacuum cleaner. Insert the hose

of the vacuum cleaner into the hole at the rear of the tool.

Rip fence (Optional accessory)

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing accessories.

1) Straight cuts (Fig. 16 & 17)

When repeatedly cutting widths of 160 mm or less,

use of the rip fence will assure fast, clean, straight

cuts.

To install, insert the rip fence into the rectangular

hole on the side of the base with the fence guide fac-

ing down. Slide the rip fence to the desired cutting

width position, then tighten the bolt to secure it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JV0600X1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info