Bedienungsanleitung Makita JV103DZJ (Seite 9 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711063

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

9 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION:

Hold the tool and the battery cartridge

rmly when installing or removing battery cartridge.

Failuretoholdthetoolandthebatterycartridgermlymay

cause them to slip off your hands and result in damage to

thetoolandbatterycartridgeandapersonalinjury.

►Fig.1: 1. Red indicator 2. Button 3. Battery cartridge

Toremovethebatterycartridge,slideitfromthetool

while sliding the button on the front of the cartridge.

Toinstallthebatterycartridge,alignthetongueonthe

battery cartridge with the groove in the housing and slip

itintoplace.Insertitallthewayuntilitlocksinplace

withalittleclick.Ifyoucanseetheredindicatoronthe

upper side of the button, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen.Ifnot,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly.Ifthecartridgedoesnotslideineasily,itis

not being inserted correctly.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutsoffpowertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the battery is operated in a manner that causes

it to draw an abnormally high current, the tool automat-

icallystopswithoutanyindication.Inthissituation,turn

the tool off and stop the application that caused the tool

tobecomeoverloaded.Thenturnthetoolontorestart.

Overheat protection

When the tool or battery is overheated, the tool stops

automaticallyandthelampblinks.Inthiscase,letthe

tool and battery cool before turning the tool on again.

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically.Ifyouturnthetoolon,themotorruns

againbutstopssoon.Inthiscase,removethebattery

from the tool and charge the battery.

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

►Fig.2: 1.Indicatorlamps2. Check button

Press the check button on the battery cartridge to indicate the remain-

ingbatterycapacity.Theindicatorlampslightupforafewseconds.

Indicator lamps Remaining

capacity

Lighted Off

75% to 100%

50% to 75%

25% to 50%

0% to 25%

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Selecting the cutting action

►Fig.3: 1. Cutting action changing lever

Thistoolcanbeoperatedwithanorbitalorastraight

line(upanddown)cuttingaction.Theorbitalcutting

actionthruststhejigsawbladeforwardonthecutting

stroke and greatly increases cutting speed.

Tochangethecuttingaction,justturnthecuttingaction

changing lever to the desired cutting action position.

Refer to the table to select the appropriate cutting action.

Position Cutting action Applications

0 Straight line cutting

action

For cutting mild

steel, stainless

steel and plastics.

For clean cuts in

wood and plywood.

I Small orbit cutting

action

For cutting mild

steel, aluminum

and hard wood.

II Medium orbit

cutting action

For cutting wood

and plywood.

For fast cutting in

aluminum and mild

steel.

III Large orbit cutting

action

For fast cutting in

wood and plywood.

Switch action

Toturnonthetool,pressthelock/unlockbutton.Thetool

turnsintothestandbymode.Tostartthetool,pulltheswitch

triggerinthestandbymode.Tostopthetool,releasethe

switchtrigger.Thetoolturnsintothestandbymode.Toturn

off the tool, press the lock/unlock button in the standby mode.

For continuous operation, pull the switch trigger in the

standbymode,andthenpushinthelockonbutton.Tostop

the tool, pull the switch trigger fully, and then release it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JV103DZJ Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info