Bedienungsanleitung Makita JV183D (Seite 8 von 17) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691882

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

To change the cutting action, just turn the cutting action

changing lever to the desired cutting action position. Refer

to the table to select the appropriate cutting action.

006582

Switch action (Fig. 3)

CAUTION:

• Before installing the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

• When not operating the tool, depress the lock-off

button from A side to lock the switch trigger in the OFF

position.

To prevent the switch trigger from accidentally pulled, the

lock-off button is provided.

To start the tool, depress the lock-off button from B side

and pull the switch trigger.

Tool speed is increased by increasing pressure on the

switch trigger. Release the switch trigger to stop. After

use, always press in the lock-off button from A side.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing or removing saw blade (Fig. 4)

CAUTION:

• Always clean out all chips or foreign matter adhering to

the blade and/or blade holder. Failure to do so may

cause insufficient tightening of the blade, resulting in a

serious personal injury.

• Do not touch the blade or the workpiece immediately

after operation; they may be extremely hot and could

burn your skin.

• Always secure the blade firmly. Insufficient tightening

of the blade may cause blade breakage or serious

personal injury.

• Use only B type blades. Using blades other than B type

blades causes insufficient tightening of the blade,

resulting in a serious personal injury. (Fig. 5)

To install the blade, loosen the bolt counterclockwise on

the blade holder with the hex wrench.

With the blade teeth facing forward, insert the blade into

the blade holder as far as it will go. Make sure that the

back edge of the blade fits into the roller. Then tighten the

bolt clockwise to secure the blade.

To remove the blade, follow the installation procedure in

reverse.

NOTE:

• Occasionally lubricate the roller.

Hex wrench storage (Fig. 6)

When not in use, store the hex wrench as shown in the

figure to keep it from being lost.

First, insert the hex wrench into the hole. Then push it into

the hook until it locked.

Dust cover (Fig. 7)

CAUTION:

• Always wear safety goggles even when operating the

tool with the dust cover lowered.

Lower the dust cover to prevent chips from flying.

However, when making bevel cuts, raise it all the way.

OPERATION

CAUTION:

• Always hold the base flush with the workpiece. Failure

to do so may cause blade breakage, resulting in a

serious injury.

• Advance the tool very slowly when cutting curves or

scrolling. Forcing the tool may cause a slanted cutting

surface and blade breakage. (Fig. 8)

Turn the tool on without the blade making any contact and

wait until the blade attains full speed. Then rest the base

flat on the workpiece and gently move the tool forward

along the previously marked cutting line.

Bevel cutting (Fig. 9)

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before tilting the base.

• Raise the dust cover all the way before making bevel

cuts. (Fig. 10)

With the base tilted, you can make bevel cuts at any angle

between 0° and 45° (left or right).

Loosen the bolt on the back of the base with the hex

wrench. Move the base so that the bolt is positioned in the

center of the cross-shaped slot in the base. (Fig. 11)

Tilt the base until the desired bevel angle is obtained. The

edge of the motor housing indicates the bevel angle by

graduations. Then tighten the bolt to secure the base.

Front flush cuts (Fig. 12)

Loosen the bolt on the back of the base with the hex

wrench and slide the base all the way back. Then tighten

the bolt to secure the base.

Cutouts

Cutouts can be made with either of two methods A or B.

A) Boring a starting hole (Fig. 13)

For internal cutouts without a lead-in cut from an

edge, pre-drill a starting hole 12 mm or more in

diameter. Insert the blade into this hole to start your

cut.

Position Cutting action Applications

Straight line

cutting action

For cutting mild steel,

stainless steel and plastics.

For clean cuts in wood and

plywood.

Small orbit

cutting action

For cutting mild steel,

aluminum and hard wood.

Medium orbit

cutting action

For cutting wood and

plywood.

For fast cutting in aluminum

and mild steel.

III

Large orbit

cutting action

For fast cutting in wood and

plywood.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JV183D Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info