Bedienungsanleitung Makita KP0810 (Seite 7 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

599007

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

7. Be sure the blade installation bolts are securely

tightened before operation.

8. Hold the tool firmly with both hands.

9. Keep hands away from rotating parts.

10. Before using the tool on an actual workpiece, let it

run for a while. Watch for vibration or wobbling

that could indicate poor installation or a poorly

balanced blade.

11. Make sure the blade is not contacting the

workpiece before the switch is turned on.

12. Wait until the blade attains full speed before

cutting.

13. Always switch off and wait for the blades to come

to a complete stop before any adjusting.

14. Never stick your finger into the chip chute. Chute

may jam when cutting damp wood. Clean out

chips with a stick.

15. Do not leave the tool running. Operate the tool

only when hand-held.

16. Always change both blades or covers on the

drum, otherwise the resulting imbalance will

cause vibration and shorten tool life.

17. Use only Makita blades specified in this manual.

18. Always use the correct dust mask/respirator for

the material and application you are working with.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to safety

rules for the subject product.

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Adjusting depth of cut (Fig. 1)

Depth of cut may be adjusted by simply turning the knob

on the front of the tool so that the pointer points the

desired depth of cut.

Switch action (Fig. 2)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

For tool with lock button

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop.

For continuous operation, pull the switch trigger and then

push in the lock button from either side.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

For tool with lock-off button

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, depress the lock-off button from either

side and pull the switch trigger. Release the switch trigger

to stop.

Electronic function

For Model KP0810C only

The tool equipped with electronic function are easy to

operate because of the following features.

Constant speed control

Electronic speed control for obtaining constant speed.

Possible to get fine finish, because the rotating speed is

kept constant even under load condition.

Soft start

Soft-start feature minimizes start-up shock, and makes

the tool start smoothly.

Foot (Fig. 3)

After a cutting operation, raise the back side of the tool

and a foot comes under the level of the rear base. This

prevents the tool blades to be damaged.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Removing or installing planer blades

CAUTION:

• Tighten the blade installation bolts carefully when

attaching the blades to the tool. A loose installation bolt

can be dangerous. Always check to see they are

tightened securely.

• Handle the blades very carefully. Use gloves or rags to

protect your fingers or hands when removing or

installing the blades.

• Use only the Makita wrench provided to remove or

install the blades. Failure to do so may result in

overtightening or insufficient tightening of the

installation bolts. This could cause an injury.

For tool with standard planer blades (Fig. 4 - 6)

To remove the blades on the drum, unscrew the

installation bolts with the socket wrench. The drum cover

comes off together with the blades.

To install the blades, first clean out all chips or foreign

matter adhering to the drum or blades. Use blades of the

same dimensions and weight, or drum oscillation/vibration

will result, causing poor planing action and, eventually,

tool breakdown.

Place the blade on the gauge base so that the blade edge

is perfectly flush with the inside edge of the gauge plate.

Place the adjusting plate on the blade, then simply press

in the heel of the adjusting plate flush with the back side of

the gauge base and tighten two screws on the adjusting

plate. Now slip the heel of the adjusting plate into the

drum groove, then fit the drum cover on it.

Tighten all the installation bolts evenly and alternately with

the socket wrench.

For tool with mini planer blades

1. Remove the existing blade, if the tool has been in use,

carefully clean the drum surfaces and the drum cover.

To remove the blades on the drum, unscrew the three

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita KP0810 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info