Bedienungsanleitung Makita LF 1000 (Seite 20 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448577

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Your risk from these exposures varies, depend-

ing on how often you do this type of work. To

reduce your exposure to these chemicals: work

in a well ventilated area and work with approved

safety equipment, such as those dust masks

that are specially designed to filter out micro-

scopic particles.

34. Make sure that the table is securely fixed with

the lever after turning it over.

WHEN USING IN MITER SAW MODE:

35. Do not use the saw to cut other than wood, alu-

minum or similar materials.

36. Do not perform any operation freehand. The

workpiece must be secured firmly against the turn

table and guide fence with the vise during all opera-

tions. Never use your hand to secure the workpiece.

37. Ensure that the tool is stable before each cut.

38. Support long workpieces with appropriate addi-

tional supports.

39. Never cut so small workpiece which cannot be

securely held by the vise. Improperly held work-

piece may cause kickback and serious personal

injury.

40. Make sure that the turn table is properly secured

so it will not move during operation.

41. Make sure that the arm is securely fixed when

beveling. Tighten the lever clockwise to fix the

arm.

42. Make sure the blade does not contact the turn

table in the lowest position and is not contacting

the workpiece before the switch is turned on.

43. Hold the handle firmly. Be aware that the saw

moves up or down slightly during start-up and

stopping.

WHEN USING IN THE TABLE SAW (BENCH SAW)

MODE:

44. Do not perform any operation freehand. Free-

hand means using your hands to support or

guide the workpiece, in lieu of a rip fence.

45. Make sure that the turn table is fixed securely.

46. Make sure that the arm is securely fixed in the

working position. Tighten the lever clockwise to

fix the arm.

47. Use a push stick or a push block to avoid work-

ing with the hands and fingers close to the saw

blade.

48. Make sure the blade is not contacting the riving

knife or workpiece before the switch is turned

on.

49. Pay particular attention to instructions for reduc-

ing risk of KICKBACK. KICKBACK is a sudden

reaction to a pinched, bound or misaligned saw

blade. KICKBACK causes the ejection of the

workpiece from the tool back towards the opera-

tor. KICKBACKS CAN LEAD TO SERIOUS PER-

SONAL INJURY. Avoid KICKBACKS by keeping

the blade sharp, by keeping the rip fence parallel

to the blade, by keeping the riving knife and

blade guard in place and operating properly, by

not releasing the workpiece until you have

pushed it all the way past the blade, and by not

ripping a workpiece that is twisted or warped or

does not have a straight edge to guide along the

fence.

50. Avoid abrupt, fast feeding. Feed as slowly as

possible when cutting hard workpieces. Do not

bend or twist workpiece while feeding. If you

stall or jam the blade in the workpiece, turn the

tool off immediately. Unplug the tool. Then clear

the jam.

51. Before turning over the tool, always make sure

that the stopper pin has securely locked the tool

head in the lowest position.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this instruc-

tion manual may cause serious personal injury.

INSTALLATION

CAUTION:

• Keep the floor area around the tool level well main-

tained and free of loose materials such as chips and

cut-offs.

Bench mounting (Fig. 1, 2 & 3)

For the fully-extended feet set up as the high table

When the tool cannot be set up stable, turn the adjusting

nut at the foot of the tool for proper stability. Turn counter-

clockwise in top viewing to make the foot shorter and

clockwise in top viewing to make it longer. After adjust-

ment, make sure that the tool keep stable.

Install the fix plates with its angled end pointing outwards

onto three feet of the tool with hex bolts. And secure the

tool to the stable and level surface using bolt holes pro-

vided in the fix plates with three bolts.

For the folded feet set up as the low table

When the tool is ready in the foot-folded position, secure

the tool by using U-shaped grooves shown in the figure.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Blade guard (Fig. 4, 5 & 6)

CAUTION:

• Make sure that the handle cannot be lowered without

pushing the lever nearby the handle to the left.

• Make sure that the lower blade guards A dose not open

unless the lever near the handle is pushed at the top-

most position of the handle.

• Make sure that the lower blade guard C is installed

before using in miter saw mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LF 1000 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita LF 1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info