Bedienungsanleitung Makita LS 1013F (Seite 14 von 27) (Englisch, Holländisch)

448586

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

Holders (Fig. 29)

The holders can be installed on either side as a conve-

nient means of holding workpieces horizontally. Slip the

holder rods into the holes in the base and adjust their

length according to the workpiece to be held. Then

tighten the holders securely with the screws.

OPERATION

CAUTION:

• Before use, be sure to release the handle from the low-

ered position by pulling the stopper pin.

• Make sure the blade is not contacting the workpiece,

etc. before the switch is turned on.

• Do not apply excessive pressure on the handle when

cutting. Too much force may result in overload of the

motor and/or decreased cutting efficiency.

• Gently press down the handle to perform the cut. If the

handle is pressed down with force or if lateral force is

applied, the blade will vibrate and leave a mark (saw

mark) in the workpiece and the precision of the cut will

be impaired.

• During a slide cut, gently push the carriage toward the

guide fence without stopping. If the carriage movement

is stopped during the cut, a mark will be left in the work-

piece and the precision of the cut will be impaired.

1. Press cutting (cutting small workpieces)

(Fig. 30)

Workpieces up to 91 mm high and 70 mm wide can be

cut in the following way.

Push the carriage toward the guide fence fully and

tighten the knob to secure the carriage. Secure the work-

piece with the vise. Switch on the tool and wait until the

blade attains full speed before lowering gently into the

cut. When the cut is completed, switch off the tool and

WAIT UNTIL THE BLADE HAS COME TO A COM-

PLETE STOP before returning the blade to its fully ele-

vated position.

CAUTION:

• Firmly tighten the clamp screw on the turn base so that

the carriage will not move during operation. Insufficient

tightening may cause unexpected kickback of the

blade. Possible serious injury may result.

2. Slide (push) cutting (cutting wide workpieces)

(Fig. 31)

Workpieces up to 91 mm high and 305 mm wide can be

cut in the following way.

Loosen the knob counterclockwise so that the carriage

can slide freely. Secure the workpiece with the vise. Pull

the carriage toward you fully. Switch on the tool without

the blade making any contact and wait until the blade

attains full speed. Press down the handle and PUSH

THE CARRIAGE TOWARD THE GUIDE FENCE AND

THROUGH THE WORKPIECE. When the cut is com-

pleted, switch off the tool and WAIT UNTIL THE BLADE

HAS COME TO A COMPLETE STOP before returning

the blade to its fully elevated position.

CAUTION:

• Whenever performing the slide cut, FIRST PULL THE

CARRIAGE TOWARD YOU FULLY and press down the

handle to the fully lowered position, then PUSH THE

CARRIAGE TOWARD THE GUIDE FENCE. If you per-

form the slide cut without pulling the carriage fully or if

you perform the slide cut toward your direction, the

blade may kick back unexpectedly with the potential to

cause serious injury.

• Never perform the slide cut with the handle locked in

the lowered position by pressing the stopper pin.

3. Miter cutting

Refer to the previously covered “Positioning for adjusting

the miter angle”.

4. Bevel cut (Fig. 32)

Left and right 0°–45° bevel cuts can be performed. At a

left 45° bevel angle, workpieces up to 50 mm high and

305 mm wide can be cut. At a right 45° bevel angle,

workpieces up to 31 mm high and 305 mm wide can be

cut.

Loosen the lever and tilt the saw blade to set the bevel

angle. Be sure to re-tighten the lever firmly to secure the

selected bevel angle safely. Secure the workpiece with a

vise. Switch on the tool and wait until the blade attains

full speed. Then gently lower the handle to the fully low-

ered position while applying pressure in parallel with the

blade and PUSH THE CARRIAGE TOWARD THE

GUIDE FENCE TO CUT THE WORKPIECE. When the

cut is completed, switch off the tool and WAIT UNTIL

THE BLADE HAS COME TO A COMPLETE STOP

before returning the blade to its fully elevated position.

CAUTION:

• During a bevel cut, it may create a condition whereby

the piece cut off will come to rest against the side of the

blade. If the blade is raised while the blade is still rotat-

ing, this piece may be caught by the blade, causing

fragments to be scattered which is dangerous. The

blade should be raised ONLY after the blade has come

to a complete stop.

• When pressing down the handle, apply pressure in par-

allel with the blade. If a force is applied perpendicularly

to the turn base or if the pressure direction is changed

during a cut, the precision of the cut will be impaired.

5. Compound cutting

Compound cutting is the process in which a bevel angle

is made at the same time in which a miter angle is being

cut on a workpiece. Compound cutting can be performed

at angle shown in the table.

At the miter angle of left and right 45° and bevel angle of

left 45°, workpieces up to 50 mm high and 215 mm wide

can be cut.

At the miter angle of left and right 45° and bevel angle of

right 45°, workpieces up to 31 mm high and 215 mm

wide can be cut.

When performing compound cutting, refer to “Press cut-

ting”, “Slide cutting”, “Miter cutting” and “Bevel cut” expla-

nations.

Miter angle Bevel angle

Left 0°–47°

and Right 0°–40°

Left and Right 0°–45°

Right 52°

Left 0°–40°

and Right 0°–45°

Makita LS 1013F Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita LS 1013F

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info