Bedienungsanleitung Makita LS 1016 (Seite 15 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448591

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Special Max. Cutting capacities

No load speed (min

–1

) ............................................................................................................................................ 3,200

Laser Type (LS1016L only)............................................................................Red Laser 650 nm, <1mW (Laser Class 2)

Dimensions (L x W x H) .....................................................................................................718 mm x 640 mm x 671 mm

Net weight

For all countries other than European countries................................................................................................ 23.7 kg

For European countries..................................................................................................................................... 24.2 kg

Safety class ............................................................................................................................................................. /II

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

Intended use

The tool is intended for accurate straight and miter cut-

ting in wood. With appropriate saw blades, aluminum can

also be sawed.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES FOR TOOL

ENB034-3

1. Wear eye protection.

2. Keep hands out of path of saw blade. Avoid con-

tact with any coasting blade. It can still cause severe

injury.

3. Do not operate saw without guards in place.

Check blade guard for proper closing before

each use. Do not operate saw if blade guard

does not move freely and close instantly. Never

clamp or tie the blade guard into the open posi-

tion.

4. Do not perform any operation freehand. The

workpiece must be secured firmly against the turn

base and guide fence with the vise during all opera-

tions. Never use your hand to secure the workpiece.

5. Never reach around saw blade.

6. Turn off tool and wait for saw blade to stop

before moving workpiece or changing settings.

7. Unplug tool before changing blade or servicing.

8. Always secure all moving portions before carry-

ing the tool.

9. Stopper pin which locks the cutter head down is

for carrying and storage purposes only and not

for any cutting operations.

10. Don’t use the tool in the presence of flammable liq-

uids or gases.

11. Check the blade carefully for cracks or damage

before operation.

Replace cracked or damaged blade immediately.

12. Use only flanges specified for this tool.

13. Be careful not to damage the arbor, flanges (espe-

cially the installing surface) or bolt. Damage to these

parts could result in blade breakage.

14. Make sure that the turn base is properly secured so

it will not move during operation.

15. For your safety, remove the chips, small pieces, etc.

from the table top before operation.

16. Avoid cutting nails. Inspect for and remove all nails

from the workpiece before operation.

17. Make sure the shaft lock is released before the

switch is turned on.

18. Be sure that the blade does not contact the turn

base in the lowest position.

19. Hold the handle firmly. Be aware that the saw moves

up or down slightly during start-up and stopping.

20. Make sure the blade is not contacting the workpiece

before the switch is turned on.

21. Before using the tool on an actual workpiece, let it

run for a while. Watch for vibration or wobbling that

could indicate poor installation or a poorly balanced

blade.

22. Wait until the blade attains full speed before cutting.

23. Stop operation immediately if you notice anything

abnormal.

24. Do not attempt to lock the trigger in the on position.

25. Be alert at all times, especially during repetitive,

monotonous operations. Don’t be lulled into a false

sense of security. Blades are extremely unforgiving.

26. Always use accessories recommended in this man-

ual. Use of improper accessories such as abrasive

wheels may cause an injury.

27. Do not use the saw to cut other than aluminum,

wood or similar materials.

28. Connect miter saws to a dust collecting device

when sawing.

29. Select saw blades in relation to the material to

be cut.

30. Take care when slotting.

31. Replace the kerf board when worn.

32. Do not use saw blades manufactured from high

speed steel.

33. Some dust created from operation contains

chemicals known to cause cancer, birth defects

or other reproductive harm. Some examples of

these chemicals are:

• lead from lead-based-painted material and,

• arsenic and chromium from chemically-treated

lumber.

Crown molding 45° type

(with Crown molding stopper used)

168 mm

Base board (H)

(with Horizontal vise used)

120 mm

Makita LS 1016 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info