Bedienungsanleitung Makita LS 1017L (Seite 12 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448594

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Symbols END223-1

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

............. Read instruction manual.

............. DOUBLE INSULATION

......... To avoid injury from flying debris, keep

holding the saw head down, after making

cuts, until the blade has come to a

complete stop.

When performing slide cut, first pull

carriage fully and press down handle,

then push carriage toward the guide

fence.

............. Do not place hand or fingers close to the

blade.

.......... Adjust sliding fences clear of blade and

blade guard properly.

...... Never look into the laser beam. Direct

laser beam may injure your eyes.

Intended use

ENE006-1

The tool is intended for accurate straight and miter cutting

in wood. With appropriate saw blades, aluminum can also

be sawed.

Power supply

ENF002-1

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

General Power Tool Safety

Warnings GEA010-1

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

ADDITIONAL SAFETY RULES

FOR TOOL

ENB034-6

1. Wear eye protection.

2. Keep hands out of path of saw blade. Avoid

contact with any coasting blade. It can still cause

severe injury.

3. Do not operate saw without guards in place.

Check blade guard for proper closing before each

use. Do not operate saw if blade guard does not

move freely and close instantly. Never clamp or tie

the blade guard into the open position.

4. Do not perform any operation freehand. The

workpiece must be secured firmly against the turn

base and guide fence with the vise during all

operations. Never use your hand to secure the

workpiece.

5. Never reach around saw blade.

6. Turn off tool and wait for saw blade to stop before

moving workpiece or changing settings.

7. Unplug tool before changing blade or servicing.

8. Always secure all moving portions before carrying

the tool.

9. Stopper pin which locks the cutter head down is

for carrying and storage purposes only and not for

any cutting operations.

10. Do not use the tool in the presence of flammable

liquids or gases. The electrical operation of the tool

could create an explosion and fire when exposed to

flammable liquids or gases.

11. Check the blade carefully for cracks or damage

before operation.

Replace cracked or damaged blade immediately.

12. Use only flanges specified for this tool.

13. Be careful not to damage the arbor, flanges

(especially the installing surface) or bolt. Damage

to these parts could result in blade breakage.

14. Make sure that the turn base is properly secured

so it will not move during operation.

15. For your safety, remove the chips, small pieces,

etc. from the table top before operation.

16. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

17. Make sure the shaft lock is released before the

switch is turned on.

18. Be sure that the blade does not contact the turn

base in the lowest position.

19. Hold the handle firmly. Be aware that the saw

moves up or down slightly during start-up and

stopping.

20. Make sure the blade is not contacting the

workpiece before the switch is turned on.

21. Before using the tool on an actual workpiece, let it

run for a while. Watch for vibration or wobbling

that could indicate poor installation or a poorly

balanced blade.

22. Wait until the blade attains full speed before

cutting.

23. Stop operation immediately if you notice anything

abnormal.

24. Do not attempt to lock the trigger in the on

position.

25. Be alert at all times, especially during repetitive,

monotonous operations. Do not be lulled into a

false sense of security. Blades are extremely

unforgiving.

26. Always use accessories recommended in this

manual. Use of improper accessories such as

abrasive wheels may cause an injury.

27. Do not use the saw to cut other than wood,

aluminum or similar materials.

28. Connect miter saws to a dust collecting device

when sawing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS 1017L Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info