Bedienungsanleitung Makita LS 1017L (Seite 17 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448594

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

WARNING:

• The workpiece must be secured firmly against the

turn base and guide fence with the vise during all

operations. If the workpiece is not properly secured

against the fence the material may move during the

cutting operation causing possible damage to the

blade, causing the material to be thrown and loss of

control resulting in serious personal injury.

Horizontal vise (optional accessory)

(Fig. 34)

The horizontal vise can be installed in two positions on

either the left or right side of the base. When performing

10° or greater miter cuts, install the horizontal vise on the

side opposite the direction in which the turn base is to be

turned. (Fig. 35)

By flipping the vise nut counterclockwise, the vise is

released, and rapidly moves in and out. To grip the

workpiece, push the vise knob forward until the vise plate

contacts the workpiece and flip the vise nut clockwise.

Then turn the vise knob clockwise to secure the

workpiece.

The maximum width of workpiece which can be secured

by the horizontal vise is 215 mm.

WARNING:

• Always rotate the vise nut clockwise until the

workpiece is properly secured. If the workpiece is

not properly secured the material may move during the

cutting operation causing possible damage to the

blade, causing the material to be thrown and loss of

control resulting in serious personal injury.

• When cutting a thin workpiece, such as base boards,

against the fence, always use the horizontal vise.

Holders (Fig. 36)

The holders can be installed on either side as a

convenient means of holding workpieces horizontally. Slip

fully the holder rods into the holes in the base. Then

tighten the holders securely with the screws.

WARNING:

• Always support a long workpiece so it is level with

the top surface of the turn base for an accurate cut

and to prevent dangerous loss of tool control.

Proper workpiece support will help avoid blade pinch

and possible kickback which may result in serious

personal injury.

OPERATION

NOTICE:

• Before use, be sure to release the handle from the

lowered position by pulling the stopper pin.

• Do not apply excessive pressure on the handle when

cutting. Too much force may result in overload of the

motor and/or decreased cutting efficiency. Push down

handle with only as much force as is necessary for

smooth cutting and without significant decrease in

blade speed.

• Gently press down the handle to perform the cut. If the

handle is pressed down with force or if lateral force is

applied, the blade will vibrate and leave a mark (saw

mark) in the workpiece and the precision of the cut will

be impaired.

• During a slide cut, gently push the carriage toward the

guide fence without stopping. If the carriage movement

is stopped during the cut, a mark will be left in the

workpiece and the precision of the cut will be impaired.

WARNING:

• Make sure the blade is not contacting the

workpiece, etc. before the switch is turned on.

Turning the tool on with the blade in contact with the

workpiece may result in kickback and serious personal

injury.

1. Press cutting (cutting small workpieces) (Fig. 37)

Workpieces up to 91 mm high and 70 mm wide can be

cut in the following manner.

Push the carriage toward the guide fence fully and

tighten the locking screw clockwise to secure the

carriage. Secure the workpiece correctly with the

proper type of vise. Switch on the tool without the

blade making any contact and wait until the blade

attains full speed before lowering. Then gently lower

the handle to the fully lowered position to cut the

workpiece. When the cut is completed, switch off the

tool and WAIT UNTIL THE BLADE HAS COME TO A

COMPLETE STOP before returning the blade to its

fully elevated position.

WARNING:

• Firmly tighten the knob clockwise so that the

carriage will not move during operation. Insufficient

tightening of the knob may cause possible kickback

which may result in serious personal injury.

2. Slide (push) cutting (cutting wide workpieces)

(Fig. 38)

Loosen the locking screw counterclockwise so that the

carriage can slide freely. Secure the workpiece with

the proper type of vise. Pull the carriage toward you

fully. Switch on the tool without the blade making any

contact and wait until the blade attains full speed.

Press the handle down and PUSH THE CARRIAGE

TOWARD THE GUIDE FENCE AND THROUGH THE

WORKPIECE. When the cut is completed, switch off

the tool and WAIT UNTIL THE BLADE HAS COME

TO A COMPLETE STOP before returning the blade to

its fully elevated position.

WARNING:

• Whenever performing a slide cut, first pull the

carriage full towards you and press the handle all

the way down, then push the carriage toward the

guide fence. Never start the cut with the carriage

not pulled fully toward you. If you perform the slide

cut without the carriage pulled fully toward you

unexpected kickback may occur and serious personal

injury may result.

• Never attempt to perform a slide cut by pulling the

carriage towards you. Pulling the carriage towards

you while cutting may cause unexpected kickback

resulting in possible serious personal injury.

• Never perform the slide cut with the handle locked in

the lowered position.

• Never loosen the locking screw which secures the

carriage while the blade is rotating. A loose carriage

Makita LS 1017L Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info