Bedienungsanleitung Makita LS 1018 (Seite 13 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448595

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

26. Always use accessories recommended in this

manual. Use of improper accessories such as

abrasive wheels may cause an injury.

27. Do not use the saw to cut other than wood,

aluminum or similar materials.

28. Connect miter saws to a dust collecting device

when sawing.

29. Select saw blades in relation to the material to be

cut.

30. Take care when slotting.

31. Replace the kerf board when worn.

32. Do not use saw blades manufactured from high

speed steel.

33. Some dust created from operation contains

chemicals known to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicals are:

• lead from lead-based-painted material and,

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies,

depending on how often you do this type of

work. To reduce your exposure to these

chemicals: work in a well ventilated area and

work with approved safety equipment, such as

those dust masks that are specially designed to

filter out microscopic particles.

34. To reduce the emitted noise, always be sure that

the blade is sharp and clean.

35. The operator is adequately trained in the use,

adjustment and operation of the machine.

36. Use correctly sharpened saw blades. Observe the

maximum speed marked on the saw blade.

37. Refrain from removing any cut-offs or other parts

of the workpiece from the cutting area whilst the

tool is running and the saw head is not in the rest

position.

38. Use only saw blades recommended by the

manufacturer which conform to EN847-1.

39. Wear gloves for handling saw blade (saw blades

shall be carried in a holder wherever practicable)

and rough material.

40. When fitted with laser, no exchange with different

type of laser is permitted. Repairs shall only be

carried out correctly.

SAVE THESE INSTRUCTIONS.

INSTALLATION

Bench mounting (Fig. 1)

When the tool is shipped, the handle is locked in the

lowered position by the stopper pin. Release the stopper

pin by simultaneously applying a slight downward

pressure on the handle and pulling the stopper pin.

(Fig. 2)

This tool should be bolted with four bolts to a level and

stable surface using the bolt holes provided in the tool’s

base. This will help prevent tipping and possible injury.

FUNCTIONAL DESCRIPTION

WARNING:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function

on the tool. Failure to switch off and unplug the tool

may result in serious personal injury from accidental

start-up.

Blade guard (Fig. 3)

When lowering the handle, the blade guard rises

automatically. The blade guard returns to its original

position when the cut is completed and the handle is

raised.

WARNING:

• Never defeat or remove the blade guard or the

spring which attaches to the guard. An exposed

blade as a result of defeated guarding may result in

serious personal injury during operation.

In the interest of your personal safety, always maintain the

blade guard in good condition. Any irregular operation of

the blade guard should be corrected immediately. Check

to assure spring loaded return action of guard.

WARNING:

• Never use the tool if the blade guard or spring are

damaged, faulty or removed. Operation of the tool

with a damaged, faulty or removed guard may result in

serious personal injury.

If the see-through blade guard becomes dirty, or sawdust

adheres to it in such a way that the blade and/or

workpiece is no longer easily visible, unplug the saw and

clean the guard carefully with a damp cloth. Do not use

solvents or any petroleum-based cleaners on the plastic

guard because this may cause damage to the guard.

If the blade guard becomes dirty and needs to be cleaned

for proper operation follow the steps below:

With the tool switched off and unplugged, use the

supplied socket wrench to loosen the hex bolt holding the

center cover. Loosen the hex bolt by turning it

counterclockwise and raise the blade guard and center

cover. (Fig. 4)

With the blade guard so positioned, cleaning can be more

completely and efficiently accomplished. When cleaning

is complete reverse procedure above and secure bolt. Do

not remove spring holding blade guard. If guard becomes

damaged through age or UV light exposure, contact a

Makita service center for a new guard. DO NOT DEFEAT

OR REMOVE GUARD.

Positioning kerf board (Fig. 5 & 6)

This tool is provided with the kerf boards in the turn base

to minimize tearing on the exit side of a cut. The kerf

boards are factory adjusted so that the saw blade does

not contact the kerf boards. Before use, adjust the kerf

boards as follows:

First, unplug the tool. Loosen all the screws (3 each on left

and right) securing the kerf boards. Re-tighten them only

to the extent that the kerf boards can still be easily moved

by hand. Lower the handle fully and push in the stopper

pin to lock the handle in the lowered position. Loosen the

screw which secures the slide poles. Pull the carriage

toward you fully. Adjust the kerf boards so that the kerf

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS 1018 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info