Bedienungsanleitung Makita LS 1030 (Seite 6 von 14) (Englisch, Holländisch)

448590

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

ENGLISH

Explanation of general view

1 Bolt

2 Center cover

3 Socket wrench

4 Safety cover

5 Loosen

6 Shaft lock

7 Arrow

8 Blade case

9 Arrow

0 Saw blade

q Flange

w Spindle

e Ring

r Flange

t Hex bolt

y Dust spout

u Elbow

i Dust bag

o Fastener

p Switch trigger

a Lever

s Turn base

d Kerf board

f Depth adjusting bolt

g Guide fence

h Pointer

j Miter scale

k Grip

l Clamp screw

; Vise arm

z Screw

x Workpiece

c Cutting line

v Groove

b Support

n Screw

m Wood facing

, Aluminum extrusion

. Spacer blocks

/ Bolt

¡ Wrench

™ Hex lock nut

£ Arm

¢ Wrench

∞ Triangular rule

§ Hex bolts

¶ Set plate

• Wing bolt

ª Holder

º Wing bolt

œ Carrying grip

∑ Limit mark

é Screwdriver

® Brush holder cap

† Stopper pin

SPECIFICATIONS

Model LS1030

Blade diameter ............................................. 255 mm

Max. cutting capacities (H x W)

Cross cut (90°) .......... 70 x 126 mm or 89 x 89 mm

Miter cut (45°) ............. 70 x 89 mm or 89 x 63 mm

No load speed (RPM) ...................................... 4,600

Dimensions (L xWxH)........... 470 x 485 x 510 mm

Net weight ..................................................... 10.6 kg

•

Due to the continuing program of research and

development, the specifications herein are subject

to change without prior notice.

•

Note: Specifications may differ from country to

country.

Power supply

The machine should be connected only to a power

supply of the same voltage as indicated on the

nameplate, and canonly be operated on single-phase

AC supply. They are double-insulated in accordance

with European Standard and can, therefore, also be

used from sockets without earth wire.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

These symbols mean:

Read instruction manual.

DOUBLE INSULATION

ADDITIONAL SAFETY RULES

1. Wear eye protection.

2. Do not operate saw without guards in place.

3. Don’t use the machine in the presence of

flammable liquids or gases.

4. Check the blade carefully for cracks or dam-

age before operation. Replace cracked or

damaged blade immediately.

5. Use only flanges specified for this machine.

6. Be careful not to damage the arbor, flanges

(especially the installingsurface) or bolt. Dam-

age to these parts could result in blade break-

age.

7. Make sure that the turn base is properly

secured so it will not move during operation.

8. For your safety, remove the chips, small

pieces, etc. from the table top before opera-

tion.

9. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

10. Make sure the shaft lock is released before the

switch is turned on.

11. Be sure that the blade does not contact the

turn base in the lowest position.

12. Hold the handle firmly. Be aware that the saw

moves up or down slightly during start-up and

stopping.

13. Do not perform any operation freehand. The

workpiece must be secured firmly against the

turn base and guide fence during all opera-

tions.

14. Keep hands out of path of saw blade. Avoid

contact with any coasting blade. It can still

cause severe injury.

15. Never reach around saw blade.

16. Make sure the blade is not contacting the

workpiece before the switch is turned on.

17. Before using the machine on an actual work-

piece, let it run for a while. Watch for vibration

or wobbling that could indicate poor installa-

tion or a poorly balanced blade.

18. Wait until the blade attains full speed before

cutting.

19. Stop operation immediately if you notice any-

thing abnormal.

20. Do not attempt to lock the trigger in the on

position.

21. Shut off power and wait for saw blade to stop

before servicing or adjusting machine.

LS1030 (E) (’97. 3. 6)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS 1030 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita LS 1030

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info