Bedienungsanleitung Makita LS 1030 (Seite 8 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448590

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Kerf board (Fig. 11)

This machine is provided with the kerf board in the

turn base. If the kerf groove has not yet been cut in

the kerf board by the factory, you should cut the

groove before actually using the machine to cut a

workpiece. Switch on the machine and lower the

blade gently to cut a groove in the kerf board.

Maintaining maximum cutting capacity

(Fig. 12 & 13)

Unplug the machine before any adjustment is

attempted. This machine is factory adjusted to pro-

vide the max. cutting capacity for a 255 mm saw

blade. When the diameter of the blade has been

reduced due to sharpening, adjust the depth adjusting

bolt by turning it with the socket wrench. The saw

blade is lowered by turning the depth adjusting bolt

counterclockwise and raised by turning it clockwise.

Adjust so that when the handle is in the fully lowered

position, there will be a distance of about 126 mm

from the front face of the guide fence to the point

where the front edge of the blade enters the kerf. With

the machine unplugged, rotate the blade by hand

while holding the handle all the way down. Be sure

that the blade does not contact any part of the lower

base when the handle is lowered completely.

Positioning for adjusting the miter angle

(Fig. 14)

Loosen the grip by turning counterclockwise. This

allows the turn base to turn freely. When you have

moved the grip to the position where the pointer

indicates the desired angle on the miter scale,

securely tighten the grip clockwise.

CAUTION:

When turning the turn base, be sure to raise the

handle fully.

Securing workpiece (Fig. 15)

WARNING:

It is extremely important to always secure the work-

piece properly and tightly with the vise. Failure to do

so can cause the machine to be damaged and/or the

workpiece to be destroyed. PERSONAL INJURY MAY

ALSO RESULT. Also, after a cutting operation, DO

NOT raise the blade until the blade has come to a

complete stop.

Secure the turn base firmly at the position of the

desired miter angle. Position the vise arm according

to the thickness and shape of the workpiece and

secure the vise arm by tightening the screw. Press the

workpiece flat against the guide fence and the turn

base. Position the workpiece at the desired cutting

position and secure it firmly by tightening the clamp

screw.

Operation (Fig. 16 & 17)

When cutting with this machine, the thickness of the

blade is cut out of the workpiece as well. Therefore,

your cutting line should be on either the left or right

side of the groove in the kerf board. Switch on the

machine and wait until the blade attains full speed

before lowering gently into the cut. When the blade

contacts the workpiece, gradually bear down on the

handle to perform the cut. When the cut is completed,

switch off the machine and WAIT UNTIL THE BLADE

HAS COME TO ACOMPLETE STOP before returning

the blade to its fully elevated position. A thin piece of

cut off material could otherwise contact the coasting

blade and be thrown around dangerously.

CAUTION:

When cutting long workpieces, use supports that are

as high as the top surface level of the turn base.

Wood facing (Fig. 18)

Use of wood facing helps to assure splinter-free cuts in workpieces. Attach a wood facing to the guide fence

using the holes in the guide fence.

CAUTION:

•

Use straight wood of even thickness as the wood facing.

•

See the figure below concerning the dimensions for a suggested wood facing.

•

Use screws to attach the wood facing to the guide fence. The screws should be installed so that the screw

heads are below the surface of the wood facing.

•

When the wood facing is attached, do not turn the turn base with the handle lowered. The wood facing will

be damaged.

NOTE:

When the wood facing is attached, the max. cutting capacities in width (126 mm at 0°, 89 mm at 45°) will be

reduced by thickness of the wood facing.

Over

10 mm

Over 460 mm

117 mm 117 mm

25 mm

89 mm

LS1030 (E) (’97. 3. 6)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS 1030 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita LS 1030

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info