Bedienungsanleitung Makita LS 1216F (Seite 23 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448602

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

5. Compound cutting

Compound cutting is the process in which a bevel angle

is made at the same time in which a miter angle is being

cut on a workpiece. Compound cutting can be performed

at the angle shown in the table.

When performing compound cutting, refer to “Press cut-

ting”, “Slide cutting”, “Miter cutting” and “Bevel cut” expla-

nations.

6. Cutting crown and cove moldings

Crown and cove moldings can be cut on a compound

miter saw with the moldings laid flat on the turn base.

There are two common types of crown moldings and one

type of cove moldings; 52/38° wall angle crown molding,

45° wall angle crown molding and 45° wall angle cove

molding. See illustrations. (Fig. 46)

There are crown and cove molding joints which are made

to fit “Inside” 90° corners ((1) and (2) in Fig. 47 & 48) and

“Outside” 90° corners ((3) and (4) in Fig. 47 & 48).

Measuring

Measure the wall length and adjust workpiece on table to cut wall contact edge to desired length. Always make sure

that cut workpiece length at the back of the workpiece is the same as wall length. Adjust cut length for angle of cut.

Always use several pieces for test cuts to check the saw angles.

When cutting crown and cove moldings, set the bevel angle and miter angle as indicated in the table (A) and position

the moldings on the top surface of the saw base as indicated in the table (B).

In the case of left bevel cut

Tabl e (A )

Tabl e (B )

Example:

In the case of cutting 52/38° type crown molding for position (1) in Fig. 47 & 48:

• Tilt and secure bevel angle setting to 33.9° LEFT.

• Adjust and secure miter angle setting to 31.6° RIGHT.

• Lay crown molding with its broad back (hidden) surface down on the turn base with its CEILING CONTACT EDGE

against the guide fence on the saw.

• The finished piece to be used will always be on the LEFT side of the blade after the cut has been made.

In the case of right bevel cut

Tabl e (A )

Miter angle Bevel angle

Left and Right 0° – 45° Left and Right 0° – 45°

Molding position

in Fig. 47 & 48

Bevel angle Miter angle

52/38° type 45° type 52/38° type 45° type

For inside corner

(1)

Left 33.9° Left 30°

Right 31.6° Right 35.3°

(2)

Left 31.6° Left 35.3°

For outside corner

(3)

(4) Right 31.6° Right 35.3°

Molding position

in Fig. 47 & 48

Molding edge against guide fence Finished piece

For inside corner

(1)

Ceiling contact edge should be

against guide fence.

Finished piece will be on the Left

side of blade.

(2)

Wall contact edge should be against

guide fence.

For outside corner

(3)

Finished piece will be on the Right

side of blade.

(4)

Ceiling contact edge should be

against guide fence.

Molding position

in Fig. 47 & 48

Bevel angle Miter angle

52/38° type 45° type 52/38° type 45° type

For inside corner

(1)

Right 33.9° Right 30°

Right 31.6° Right 35.3°

(2)

Left 31.6° Left 35.3°

For outside corner

(3)

(4) Right 31.6° Right 35.3°

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS 1216F Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info