Bedienungsanleitung Makita LS0815FL (Seite 11 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598999

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

Net weight For all countries other than European countries...........................14.1 kg

For European countries........... LS0815F 14.1 kg

......... LS0815FL 14.2 kg

Safety class /II

• Due to our continuing program of research and development, the specifications herein are subject to change without

notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

Symbols

END223-4

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

............. Read instruction manual.

............. DOUBLE INSULATION

......... To avoid injury from flying debris, keep

holding the saw head down, after making

cuts, until the blade has come to a

complete stop.

When performing slide cut, first pull

carriage fully and press down handle,

then push carriage toward the guide

fence.

............. Do not place hand or fingers close to the

blade.

.......... Adjust sliding fences clear of blade and

blade guard properly.

...... LASER RADIATION: Do not stare into

beam. Direct laser beam may injure your

eyes.

............... Only for EU countries

Do not dispose of electric equipment

together with household waste material!

In observance of the European Directive,

on Waste Electric and Electronic

Equipment and its implementation in

accordance with national law, electric

equipment that have reached the end of

their life must be collected separately and

returned to an environmentally

compatible recycling facility.

Intended use

ENE006-1

The tool is intended for accurate straight and miter cutting

in wood. With appropriate saw blades, aluminum can also

be sawed.

Power supply

ENF002-2

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

General Power Tool Safety

Warnings GEA010-1

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

ADDITIONAL SAFETY RULES

FOR TOOL

ENB034-7

1. Wear eye protection.

2. Keep hands out of path of saw blade. Avoid

contact with any coasting blade. It can still cause

severe injury.

3. Do not operate saw without guards in place.

Check blade guard for proper closing before each

use. Do not operate saw if blade guard does not

move freely and close instantly. Never clamp or tie

the blade guard into the open position.

4. Do not perform any operation freehand. The

workpiece must be secured firmly against the turn

base and guide fence with the vise during all

operations. Never use your hand to secure the

workpiece.

5. Never reach around saw blade.

6. Turn off tool and wait for saw blade to stop before

moving workpiece or changing settings.

7. Unplug tool before changing blade or servicing.

8. Always secure all moving portions before carrying

the tool.

9. Stopper pin which locks the cutter head down is

for carrying and storage purposes only and not for

any cutting operations.

10. Do not use the tool in the presence of flammable

liquids or gases. The electrical operation of the tool

could create an explosion and fire when exposed to

flammable liquids or gases.

11. Check the blade carefully for cracks or damage

before operation.

Replace cracked or damaged blade immediately.

12. Use only flanges specified for this tool.

13. Be careful not to damage the arbor, flanges

(especially the installing surface) or bolt. Damage

to these parts could result in blade breakage.

14. Make sure that the turn base is properly secured

so it will not move during operation.

15. For your safety, remove the chips, small pieces,

etc. from the table top before operation.

16. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS0815FL Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info