Bedienungsanleitung Makita LS1016F (Seite 27 von 152) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

599000

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Adjustment of the laser line position (Fig. 70 & 71)

For models LS1016L and LS1016FL only

WARNING:

• Since the tool must be plugged in while adjusting

the laser line, special care must be taken to not

switch on the tool. Accidental start up of the tool may

result in serious personal injury.

CAUTION:

• Never look directly into the laser beam. Direct eye

exposure to the beam could cause serious damage to

the eyes.

• LASER RADIATION

Do not stare into beam.

NOTICE:

• Beware that impacts to the tool may cause the laser

line to be misaligned or may cause damage to the

laser, shortening its life.

Adjusting the laser line for the left side of the blade.

1 Screw to change the movable range of the adjusting

screw

2 Adjusting screw

3 Hex wrench

4 Laser line

5 Saw blade

009514

Adjusting the laser line for the right side of the blade.

1 Adjusting screw

2 Saw blade

3 Laser line

009515

For both adjustments, do as follows.

1. Make sure that the tool is unplugged.

2. Draw the cutting line on the workpiece and place it

on the turn table. At this time, do not secure the

workpiece with a vise or similar securing device.

3. Lower the blade by lowering the handle and just

check to see where the cutting line and the position

of the saw blade is. (Decide which position to cut on

the line of cut.)

4. After deciding the correct position of the line in rela-

tion to the blade, return the handle to the original

position. Secure the workpiece with the vertical vise

without shifting the workpiece from the pre-checked

position.

5. Plug the tool and turn on the laser switch.

6. Adjust the position of laser line as follows.

The position of laser line can be changed as the movable

range of the adjusting screw for the laser is changed by

turning two screws with a hex wrench. (The movable

range of laser line is factory adjusted within 1 mm from

the side surface of blade.)

To shift the laser line movable range further away from

the side surface of blade, turn the two screws counter-

clockwise after loosening the adjusting screw. Turn these

two screws clockwise to shift it closer to the side surface

of the blade after loosening the adjusting screw.

Refer to the section titled “Laser beam action” and adjust

the adjusting screw so that the cutting line on your work-

piece is aligned with the laser line.

NOTE:

• Check the position of laser line regularly for accuracy.

• Have the tool repaired by a Makita authorized service

center for any failure on the laser unit.

Cleaning the laser light lens (Fig. 72 & 73)

For models LS1016L and LS1016FL only

If the lens for the laser light becomes dirty, or sawdust

adheres to it in such a way that the laser line is no longer

easily visible, unplug the saw and remove and clean the

lens for the laser light carefully with a damp, soft cloth.

Do not use solvents or any petroleum-based cleaners on

the lens.

To remove the lens for the laser light, remove the saw

blade before removing the lens according to the instruc-

tions in the section titled “Installing or removing saw

blade”.

Loosen but do not remove the screw which secures the

lens using a screwdriver.

Pull out the lens as shown in the figure.

NOTE:

• If the lens does not come out, loosen the screw further

and pull out the lens again without removing the screw.

Replacing carbon brushes (Fig. 74 & 75)

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

After replacing brushes, plug in the tool and break in

brushes by running tool with no load for about 10 min-

utes. Then check the tool while running and electric

brake operation when releasing the switch trigger. If the

electric brake is not working correctly, have the tool

repaired by a Makita service center.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS1016F Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info