Bedienungsanleitung Makita LS1440 (Seite 7 von 76) (Deutsch, Englisch, Polnisch)

599005

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

15. Use only saw blades that are marked with a

maximum speed equal to or higher than the no

load speed marked on the tool.

16. When the tool is fitted with a laser or LED, do

not replace the laser or LED with a different

type. Ask an authorized service center for repair.

17. Never remove any cut-offs or other parts of the

workpiece from the cutting area whilst the tool

is running with an unguarded saw blade.

18.

Do not perform any operation freehand.

The

workpiece must be secured firmly against the turn base

and guide fence with the vise during all operations.

Never use your hand to secure the workpiece.

19. Ensure that the tool is stable before each cut.

20. Fix the tool to a work bench, if needed.

21. Support long workpieces with appropriate

additional supports.

22.

Never cut so small workpiece which cannot be

securely held by the vise.

Improperly held workpiece

may cause kickback and serious personal injury.

23. Never reach around saw blade.

24.

Turn off tool and wait for saw blade to stop

before moving workpiece or changing settings.

25.

Unplug tool before changing blade or servicing.

26. Stopper pin which locks the cutter head down

is for carrying and storage purposes only and

not for any cutting operations.

27.

Do not use the tool in the presence of

flammable liquids or gases.

The electrical

operation of the tool could create an explosion and

fire when exposed to flammable liquids or gases.

28. Use only flanges specified for this tool.

29.

Be careful not to damage the arbor, flanges

(especially the installing surface) or bolt. Damage

to these parts could result in blade breakage.

30. Make sure that the turn base is properly

secured so it will not move during operation.

31.

For your safety, remove the chips, small pieces,

etc. from the table top before operation.

32.

Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

33.

Make sure the shaft lock is released before the

switch is turned on.

34.

Be sure that the blade does not contact the

turn base in the lowest position.

35.

Hold the handle firmly. Be aware that the saw

moves up or down slightly during start-up and

stopping.

36.

Make sure the blade is not contacting the

workpiece before the switch is turned on.

37.

Before using the tool on an actual workpiece,

let it run for a while. Watch for vibration or

wobbling that could indicate poor installation

or a poorly balanced blade.

38.

Wait until the blade attains full speed before

cutting.

39.

Stop operation immediately if you notice

anything abnormal.

40.

Do not attempt to lock the trigger in the on

position.

41.

Be alert at all times, especially during

repetitive, monotonous operations. Do not be

lulled into a false sense of security. Blades are

extremely unforgiving.

42.

Always use accessories recommended in this

manual. Use of improper accessories such as

abrasive wheels may cause an injury.

43.

Take care when slotting.

44.

Some dust created from operation contains

chemicals known to cause cancer, birth

defects or other reproductive harm. Some

examples of these chemicals are:

• lead from lead-based-painted material and,

• arsenic and chromium from

chemically-treated lumber.

Your risk from these exposures varies,

depending on how often you do this type of

work. To reduce your exposure to these

chemicals: work in a well ventilated area and

work with approved safety equipment, such as

those dust masks that are specially designed

to filter out microscopic particles.

45.

To reduce the emitted noise, always be sure

that the blade is sharp and clean.

46.

The operator is adequately trained in the use,

adjustment and operation of the machine.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this

instruction manual may cause serious personal

injury.

INSTALLATION

Bench mounting

When the tool is shipped, the handle is locked in the

lowered position by the handle latch. Release the handle

latch by lowering the handle slightly and turn the handle

latch to the released position.

Fig.1

This tool should be bolted with four bolts to a level and

stable surface using the bolt holes provided in the tool's

base. This will help prevent tipping and possible injury.

Fig.2

Installing the holders (optional accessories)

Fig.3

Fig.4

Install the holders on both sides of the base and secure

them with screws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS1440 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info