Bedienungsanleitung Makita M1901 (Seite 7 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691528

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

7 ENGLISH

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and unplugged before carrying out

any work on the tool.

Removing or installing planer

blades

CAUTION: Tighten the blade installation bolts

carefully when attaching the planer blades to

the tool.Alooseinstallationboltcanbedangerous.

Always check to see they are tightened securely.

CAUTION: Handle the planer blades very

carefully. Use gloves or rags to protect your n-

gers or hands when removing or installing the

blades.

CAUTION: Use only the Makita wrench

provided to remove or install the planer blades.

Failure to do so may result in overtightening or insuf-

cienttighteningoftheinstallationbolts.Thiscould

causeaninjury.

For tool with conventional planer

blades

Toremovetheplanerbladesonthedrum,unscrewthe

installationboltswiththesocketwrench.Thedrumcover

comesofftogetherwiththeblades.

►Fig.4: 1. Socket wrench 2. Bolts

►Fig.5: 1. Bolts 2. Drum 3.Planerblade4. Drum cover

5.Adjustingplate6. Groove

Toinstalltheplanerblades,dothefollowingprocedure.

1. Cleanoutallchipsorforeignmatteradheringtothe

drumandplanerblades.

2. Chooseplanerbladesofthesamedimensionsand

weight.Otherwisedrumoscillation/vibrationwillresult,

causingpoorplaningactionand,eventually,toolbreakdown.

3. Usethebladegaugetosettheplanerbladescorrectly.

Puttheplanerbladeonthegaugebase.Applythecutting

edgeofthebladeontheinsideankofthegaugeplate.

►Fig.6: 1.Insideankofgaugeplate2. Blade edge

3.Planerblade4.Adjustingplate5. Screws

6. Heel 7.Backsideofgaugebase8. Gauge plate

9.Gaugebase

4. Placetheadjustingplateontheplanerblade.Press

theadjustingplatesothatitsheelisushwiththebackside

ofgaugebase.Tightentwoscrewsontheadjustingplate.

5. Sliptheheeloftheadjustingplateintothedrum

groove,thentthedrumcoveronit.

6. Tightenalltheinstallationboltsevenlyandalter-

nately with the socket wrench.

7. Repeattheprocedureabovefortheotherblade.

For tool with mini planer blades

Toreplacetheminiplanerblades,dothefollowing

procedure.

1. Carefullycleanthedrumsurfacesandthedrum

cover.

2. Unscrewthethreeinstallationboltswiththesocket

wrench.Removethedrumcover,adjustingplate,set

plateandtheminiplanerblade.

►Fig.7: 1. Socket wrench 2. Bolts

3. Usethebladegaugetosettheplanerblades

correctly.Puttheminiplanerbladeonthegaugebase.

Applythecuttingedgeofthebladeontheinsideankof

the gauge plate.

►Fig.8: 1. Screws 2.Adjustingplate3.Planerblade

locating lugs 4. Gauge plate 5. Heel of

adjustingplate6. Set plate 7.Insideankof

gauge plate 8.Gaugebase9. Back side of

gaugebase10.Miniplanerblade

4. Looselyattachtheadjustingplatetothesetplate

withthescrews.Puttheadjustingplateandsetplate

onthegaugebase.Fittheplanerbladelocatinglugson

thesetplateintotheminiplanerbladegroove.

5. Applytheheeloftheadjustingplateontotheback

sideofthegaugebaseandtightenthescrews.Check

the alignments carefully to ensure uniform cutting.

6. Sliptheheeloftheadjustingplateintothegroove

of the drum.

7. Putthedrumcoveronthesetplateandlooselyt

themontothedrumwiththethreebolts.Slipthemini

planerbladeintothespacebetweenthedrumandset

plate.Makesurethattheplanerbladelocatinglugson

thesetplatetintheminiplanerbladegroove.

►Fig.9: 1.Miniplanerblade2. Groove 3. Set plate

4. Bolts 5. Drum cover 6. Drum 7.Adjusting

plate

8. Adjusttheminiplanerbladepositionlengthwayso

thatthebladeendsareclearandequidistantfromthe

housingononesideandthemetalbracketontheother.

9. Tightenthethreeboltswiththesocketwrench

provided and rotate the drum to check the clearances

betweenthebladeendsandthetoolbody.

10. Checkthethreeboltsfornaltightness.

11. Repeattheprocedureabovefortheotherblade.

Makita M1901 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info