Bedienungsanleitung Makita M2300 (Seite 9 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691825

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

9 ENGLISH

EC Declaration of Conformity

For European countries only

Makita declares that the following Machine(s):

Designation of Machine: Compound Miter Saw

Model No./ Type: M2300

Conforms to the following European Directives:

2006/42/EC

They are manufactured in accordance with the following

standard or standardized documents: EN61029

Thetechnicalleinaccordancewith2006/42/ECis

available from:

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

1.1.2016

Yasushi Fukaya

Director

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

General power tool safety warnings

WARNING: Read all safety warnings and

all instructions. Failure to follow the warnings and

instructionsmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

MITER SAW SAFETY WARNINGS

1. Keep hands out of path of saw blade. Avoid

contact with any coasting blade. It can still

cause severe injury.

2. Check the saw blade carefully for cracks or

deformation before operation.

Replace damaged blades immediately.

3. Replace the kerf board when worn.

4. Use only saw blades specied by the manufac-

turer which conform to EN847-1.

5. Do not use saw blades manufactured from

high speed steel.

6. Wear eye protection.

7. Wear hearing protection to reduce the risk of

hearing loss.

8. Wear gloves for handling saw blade (saw

blades shall be carried in a holder wherever

practicable) and rough material.

9. Connect miter saws to a dust collecting device

when sawing.

10. Select saw blades in relation to the material to

be cut.

11. Do not use the saw to cut other than wood,

aluminum or similar materials.

12. Always secure all moving portions before car-

rying the tool. When lifting or carrying the tool,

do not use the guard as a carrying handle.

13.

Do not operate saw without guards in place.

Check blade guard for proper closing before

each use. Do not operate saw if blade guard does

not move freely and close instantly. Never clamp

or tie the blade guard into the open position.

14. Keep the oor area free of loose material e.g.

chips and cut-offs.

15. Use only saw blades that are marked with a

maximum speed equal to or higher than the no

load speed marked on the tool.

16. When the tool is tted with a laser or LED, do

not replace the laser or LED with a different

type. Ask an authorized service center for repair.

17. Never remove any cut-offs or other parts of the

workpiece from the cutting area whilst the tool

is running with an unguarded saw blade.

18. Do not perform any operation freehand. The

workpiecemustbesecuredrmlyagainstthe

turn base and guide fence with the vise during all

operations. Never use your hand to secure the

workpiece.

19. Ensure that the tool is stable before each cut.

20. Fix the tool to a work bench, if needed.

21. Support long workpieces with appropriate

additional supports.

22. Never cut so small workpiece which cannot be

securely held by the vise. Improperly held work-

piece may cause kickback and serious personal

injury.

23. Never reach around saw blade.

24. Turn off tool and wait for saw blade to stop

before moving workpiece or changing

settings.

25. Unplug tool before changing blade or

servicing.

26. Stopper pin which locks the cutter head down

is for carrying and storage purposes only and

not for any cutting operations.

27. Do not use the tool in the presence of amma-

ble liquids or gases. The electrical operation of

thetoolcouldcreateanexplosionandrewhen

exposedtoammableliquidsorgases.

28. Use only anges specied for this tool.

29. Be careful not to damage the arbor, anges

(especially the installing surface) or bolt.

Damage to these parts could result in blade

breakage.

30. Make sure that the turn base is properly

secured so it will not move during operation.

31. For your safety, remove the chips, small

pieces, etc. from the table top before

operation.

32. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

33. Make sure the shaft lock is released before the

switch is turned on.

34. Be sure that the blade does not contact the

turn base in the lowest position.

35. Hold the handle rmly. Be aware that the saw

moves up or down slightly during start-up and

stopping.

36. Make sure the blade is not contacting the

workpiece before the switch is turned on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita M2300 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info