Bedienungsanleitung Makita M4500 (Seite 6 von 16) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691532

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

6 ENGLISH

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and unplugged before carrying out

any work on the tool.

Installing or removing the recipro

saw blade

CAUTION: Always clean out all chips or for-

eign matter adhering to the blade and around the

blade clamp.Failuretodosomaycauseinsufcient

tighteningoftheblade,resultinginaseriousinjury.

For Model M4500

To install the blade, loosen the bolt on the blade clamp

with the hex wrench. Insert the blade between the blade

clampandtheslidersothatthepinontheslidertsinto

theholeinthebladeshank.Ifthepincannoteasilyt

into the hole, remove the hex wrench from the screw

andthentryagain.

Afterthepintsproperlyintothehole,tightenthescrew

clockwisesecurely.Makesurethatthebladecannotbe

extractedeventhoughyoutrytopullitout.

►Fig.4: 1. Bolt 2. Hex wrench 3. Loosen 4. Tighten

►Fig.5: 1. Recipro saw blade 2. Hole for recipro saw

blade 3. Bolt 4. Pin 5. Blade clamp

CAUTION:Ifyoutightenthescrewwithoutthe

pinonthesliderttingproperlyintheholeintheblade

shank, the pin or the blade shank will be damaged.

Thismaycausethebladetobeextractedunexpect-

edlyduringoperation.

To remove the blade, follow the installation procedure

in reverse.

For Model M4501

Toinstallthereciprosawblade,alwaysmakesurethat

the blade clamp lever (part of the blade clamp sleeve)

is in released position

on the insulation cover before

inserting the recipro saw blade. If the blade clamp lever

isinxedposition,rotatethebladeclampleverinthe

direction of the arrow so that it can be locked at the

released positon

►Fig.6: 1. Blade clamp lever 2. Released position

3. Fixed position

Insert the recipro saw blade into the blade clamp as far

asitwillgo.Thebladeclampsleeverotatesandxes

the recipro saw blade. Make sure that the recipro saw

bladecannotbeextractedeventhoughyoutrytopull

it out.

►Fig.7: 1. Recipro saw blade 2. Blade clamp sleeve

CAUTION: If you do not insert the recipro saw

blade deep enough, the recipro saw blade may be

ejected unexpectedly during operation. This can

beextremelydangerous.

CAUTION: Keep hands and ngers away from

the lever during the switching operation. Failure to

dosomaycausepersonalinjuries.

To remove the recipro saw blade, rotate the blade

clampleverinthedirectionofthearrowfully.Thereci-

pro saw blade is removed and the blade clamp lever is

xedatthereleasedposition .

►Fig.8: 1. Recipro saw blade 2. Blade clamp lever

NOTE:Ifyouremovethereciprosawbladewithout

rotatingthebladeclampleverfully,thelevermaynot

be locked in the released position

. In this case,

rotatethebladeclampleverfullyagain,thenmake

sure that the blade clamp lever locked at the released

position .

NOTE: If the lever is positioned inside the tool, switch

onthetooljustasecondtoletthebladeclampout.

Switch off and unplug the tool from the mains before

working on the blade clamp lever.

Hex wrench storage

When not in use, store the hex wrench as shown in the

guretokeepitfrombeinglost.

►Fig.9: 1. Insulation cover 2. Hex wrench

OPERATION

CAUTION: Always hold the tool rmly with

one hand on insulation cover and the other on the

switch handle.

CAUTION: Always press the shoe rmly

against the workpiece during operation. If the

shoeisremovedorheldawayfromtheworkpiece

during operation, strong vibration and/or twisting will

beproduced,causingthebladetosnapdangerously.

CAUTION: Always wear gloves to protect

your hands from hot ying chips when cutting

metal.

CAUTION: Be sure to always wear suitable

eye protection which conforms with current

national standards.

CAUTION: Always use a suitable coolant

(cutting oil) when cutting metal. Failure to do so will

cause premature blade wear.

Presstheshoermlyagainsttheworkpiece.Donot

allow the tool to bounce. Bring the recipro saw blade

into light contact with the workpiece. First, make a pilot

groove using a slower speed. Then use a faster speed

to continue cutting.

►Fig.10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita M4500 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info