Bedienungsanleitung Makita M6301D (Seite 6 von 15) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691537

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

6 ENGLISH

Adjusting the fastening torque

►Fig.5: 1.Adjustingring2.Graduation3.Arrow

Thefasteningtorquecanbeadjustedin17levelsby

turningtheadjustingring.Alignthegraduationswiththe

arrowonthetoolbody.Youcangettheminimumfas-

teningtorqueat1andmaximumtorqueat

marking.

Theclutchwillslipatvarioustorquelevelswhenset

atthenumber1to16.Theclutchdoesnotworkat

the marking.

Beforeactualoperation,driveatrialscrewintoyour

materialorapieceofduplicatematerialtodeter-

minewhichtorquelevelisrequiredforaparticular

application.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/

drill bit

►Fig.6: 1. Sleeve 2. Ring 3.Tighten

Holdtheringandturnthesleevecounterclockwiseto

openthechuckjaws.Placethedriverbit/drillbitinthe

chuckasfarasitwillgo.Holdtheringrmlyandturn

thesleeveclockwisetotightenthechuck.

Toremovethedriverbit/drillbit,holdtheringandturn

thesleevecounterclockwise.

OPERATION

CAUTION: Always insert the battery cartridge

all the way until it locks in place.Ifyoucanseethe

redindicatorontheuppersideofthebutton,itisnot

lockedcompletely.Insertitfullyuntiltheredindicator

cannotbeseen.Ifnot,itmayaccidentallyfalloutof

thetool,causinginjurytoyouorsomeonearound

you.

CAUTION: When the speed comes down

extremely, reduce the load or stop the tool to

avoid the tool damage.

Holdthetoolrmlywithonehandonthegripandthe

otherhandonthebottomofthebatterycartridgeto

control the twisting action.

►Fig.7

Screwdriving operation

CAUTION: Adjust the adjusting ring to the

proper torque level for your work.

CAUTION: Make sure that the driver bit is

inserted straight in the screw head, or the screw

and/or driver bit may be damaged.

Placethepointofthedriverbitinthescrewheadand

applypressuretothetool.Startthetoolslowlyandthen

increasethespeedgradually.Releasetheswitchtrigger

assoonastheclutchcutsin.

NOTE: When driving wood screw, pre-drill a pilot hole

2/3thediameterofthescrew.Itmakesdrivingeasier

andpreventssplittingoftheworkpiece.

Drilling operation

First,turntheadjustingringsothatthearrowpointsto

the marking.Thenproceedasfollows.

Drilling in wood

Whendrillinginwood,thebestresultsareobtainedwithwood

drillsequippedwithaguidescrew.Theguidescrewmakes

drillingeasierbypullingthedrillbitintotheworkpiece.

Drilling in metal

Topreventthedrillbitfromslippingwhenstartinga

hole,makeanindentationwithacenter-punchand

hammeratthepointtobedrilled.Placethepointofthe

drillbitintheindentationandstartdrilling.

Useacuttinglubricantwhendrillingmetals.Theexcep-

tionsareironandbrasswhichshouldbedrilleddry.

CAUTION:

Pressing excessively on the tool will

not speed up the drilling.Infact,thisexcessivepressure

willonlyservetodamagethetipofyourdrillbit,decrease

thetoolperformanceandshortentheservicelifeofthetool.

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece.Thereisatremendousforceexertedon

thetool/drillbitatthetimeofholebreakthrough.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure workpieces in a

vise or similar hold-down device.

CAUTION:

If the tool is operated continuously until

the battery cartridge has discharged, allow the tool to rest

for 15 minutes before proceeding with a fresh battery.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

TomaintainproductSAFETYandRELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

beperformedbyMakitaAuthorizedorFactoryService

Centers,alwaysusingMakitareplacementparts.

Makita M6301D Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info