Bedienungsanleitung Makita M8301D (Seite 7 von 14) (Deutsch, Englisch, Polnisch)

691540

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

7 ENGLISH

Selecting the action mode

CAUTION: Always set the ring correctly to

your desired mode mark. If you operate the tool

with the ring positioned halfway between the

mode marks, the tool may be damaged.

CAUTION: When you change the position

from " " to other modes, it may be a little dif-

culty to slide the action mode changing ring. In

this case, switch on and run the tool for a second

at the " " position, then stop the tool and slide

the ring to your desired position.

►Fig.5: 1.Actionmodechangingring2.Adjusting

ring 3. Graduation 4.Arrow

Thistoolhasthreeactionmodes.

•

Drilling mode (rotation only)

•

Hammer drilling mode (rotation with

hammering)

•

Screwdriving mode (rotation with clutch)

Selectonemodesuitableforyourwork.Turnthe

action mode changing ring and align the mark that you

selectedwiththearrowonthetoolbody.

Adjusting the fastening torque

►Fig.6: 1.Actionmodechangingring2.Adjusting

ring 3. Graduation 4.Arrow

Thefasteningtorquecanbeadjustedin16levelsby

turningtheadjustingring.Alignthegraduationswiththe

arrowonthetoolbody.Youcangettheminimumfas-

teningtorqueat1andmaximumtorqueat16.

Beforeactualoperation,driveatrialscrewintoyour

materialorapieceofduplicatematerialtodeter-

minewhichtorquelevelisrequiredforaparticular

application.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/

drill bit

►Fig.7: 1. Sleeve 2. Ring 3.Tighten

Hold the ring and turn the sleeve counterclockwise to

openthechuckjaws.Placethedriverbit/drillbitinthe

chuckasfarasitwillgo.Holdtheringrmlyandturn

the sleeve clockwise to tighten the chuck.

Toremovethedriverbit/drillbit,holdtheringandturn

the sleeve counterclockwise.

OPERATION

CAUTION: Always insert the battery cartridge

all the way until it locks in place.Ifyoucanseethe

redindicatorontheuppersideofthebutton,itisnot

lockedcompletely.Insertitfullyuntiltheredindicator

cannotbeseen.Ifnot,itmayaccidentallyfalloutof

thetool,causinginjurytoyouorsomeonearound

you.

CAUTION: When the speed comes down

extremely, reduce the load or stop the tool to

avoid the tool damage.

Holdthetoolrmlywithonehandonthegripandthe

otherhandonthebottomofthebatterycartridgeto

control the twisting action.

►Fig.8

Screwdriving operation

CAUTION: Adjust the adjusting ring to the

proper torque level for your work.

CAUTION: Make sure that the driver bit is

inserted straight in the screw head, or the screw

and/or driver bit may be damaged.

First, turn the action mode changing ring so that the

arrowonthetoolbodypointstothe marking.

Placethepointofthedriverbitinthescrewheadand

apply pressure to the tool. Start the tool slowly and then

increase the speed gradually. Release the switch trigger

as soon as the clutch cuts in.

NOTE: When driving wood screw, pre-drill a pilot hole

2/3thediameterofthescrew.Itmakesdrivingeasier

andpreventssplittingoftheworkpiece.

Hammer drilling operation

CAUTION: There is a tremendous and sud-

den twisting force exerted on the tool/drill bit

at the time of hole breakthrough, when the hole

becomes clogged with chips and particles, or

when striking reinforcing rods embedded in the

concrete.

First, turn the action mode changing ring so that the

arrowonthetoolbodypointstothe marking.The

adjustingringcanbealignedinanytorquelevelsfor

this operation.

Besuretouseatungsten-carbidetippeddrillbit.

Positionthedrillbitatthedesiredlocationforthehole,

thenpulltheswitchtrigger.Donotforcethetool.Light

pressuregivesbestresults.Keepthetoolinposition

andpreventitfromslippingawayfromthehole.

Donotapplymorepressurewhentheholebecomes

clogged with chips or particles. Instead, run the tool at

anidle,thenremovethedrillbitpartiallyfromthehole.

Byrepeatingthisseveraltimes,theholewillbecleaned

outandnormaldrillingmayberesumed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita M8301D Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info