Bedienungsanleitung Makita M9001 (Seite 4 von 22) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691557

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

ENGLISH (Original instructions)

Explanation of general view

1 Shaft lock

2 Switch trigger

3 Lock lever

4 Wheel guard

5Screw

6 Bearing box

7 Lock nut

8 Depressed center grinding

wheel

9 Inner flange

10 Lock nut wrench

11 Abrasive cut-off wheel/diamond

wheel

12 Wheel guard for abrasive cut-off

wheel/diamond wheel

13 Outer flange 78

14 Inner flange 78

15 Exhaust vent

16 Inhalation vent

17 Commutator

18 Insulating tip

19 Carbon brush

20 Brush holder cap

21 Screwdriver

SPECIFICATIONS

• Due to our continuing program of research and

development, the specifications herein are subject to

change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

ENE091-1

Intended use

The tool is intended for grinding and cutting of metal and

stone materials without the use of water.

ENF002-2

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

ENF100-1

For public low-voltage distribution systems of

between 220 V and 250 V.

Switching operations of electric apparatus cause voltage

fluctuations. The operation of this device under

unfavorable mains conditions can have adverse effects

to the operation of other equipment. With a mains

impedance equal or less than 0.24 Ohms it can be

presumed that there will be no negative effects. The

mains socket used for this device must be protected with

a fuse or protective circuit breaker having slow tripping

characteristics.

GEA010-1

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future refer-

ence.

GEB129-1

GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding or Abrasive

Cutting-Off Operations:

1. This power tool is intended to function as a

grinder or cut-off tool. Read all safety warnings,

instructions, illustrations and specifications

provided with this power tool. Failure to follow all

instructions listed below may result in electric shock,

fire and/or serious injury.

2. Operations such as sanding, wire brushing or

polishing are not recommended to be performed

with this power tool. Operations for which the

power tool was not designed may create a hazard

and cause personal injury.

3. Do not use accessories which are not

specifically designed and recommended by the

tool manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safe operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

6. Threaded mounting of accessories must match

the grinder spindle thread. For accessories

mounted by flanges, the arbour hole of the

accessory must fit the locating diameter of the

flange. Accessories that do not match the mounting

hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

Model M9000 M9001

Depressed center wheel diameter 180 mm 230 mm

Max. wheel thickness 6.0 mm 6.0 mm

Spindle thread M14 or 5/8" (country specific)

Rated speed (n) / No load speed (n

) 8,500 min

–1

6,600 min

–1

Overall length 466 mm 466 mm

Net weight 5.4 kg 5.7 kg

Safety class /II /II

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita M9001 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info