Bedienungsanleitung Makita M9203 (Seite 4 von 11) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691560

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

4 ENGLISH

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Sander safety warnings

1. Always use safety glasses or goggles.

Ordinary eye or sun glasses are NOT safety

glasses.

2. Hold the tool rmly.

3. Do not leave the tool running. Operate the tool

only when hand-held.

4. This tool has not been waterproofed, so do not

use water on the workpiece surface.

5. Ventilate your work area adequately when you

perform sanding operations.

6. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier

safety data.

7. Use of this tool to sand some products, paints

and wood could expose user to dust contain-

ing hazardous substances. Use appropriate

respiratory protection.

8. Be sure that there are no cracks or breakage

on the pad before use. Cracks or breakage

may cause a personal injury.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and unplugged before adjusting or

checking function on the tool.

Switch action

CAUTION: Before plugging in the tool, always

be sure that the tool is switched off.

►Fig.1: 1. Switch

To start the tool, press the “I (ON)” side of the switch. To

stop the tool, press the “O (OFF)” side of the switch.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and unplugged before carrying out

any work on the tool.

Installing or removing abrasive

paper

Open the paper clamp by raising on the lever to release

from the locking port and then Insert the paper end into

the clamping part, aligning the paper edges even and

parallel with the sides of the base. (Bending the paper

beforehand makes attachment easier). Once the paper

is in place, return the lever to its original position.

►Fig.2: 1. Clamping part 2. Abrasive paper 3. Clamp

lever

Repeat the same process for the other end of the base,

maintaining the proper paper tension.

After inserting the paper, make sure the clamping part

hold it securely. Otherwise the paper will be loose and

subjecttoslippage,resultinginunevensandingoperation.

When you use an abrasive paper without dust-suction holes,

punch holes with the punch plate (optional accessory).

Place the punch plate over the paper so that the guide

ofthepunchplateisushwiththesidesofthebase.

Then press the punch plate to make holes in the paper.

►Fig.3: 1. Punch plate

To remove the paper, release the paper clamp as stated

above.

Dust bag

►Fig.4: 1. Dust spout 2. Dust bag

Attach the dust bag onto the dust spout. The dust spout

is tapered. When attaching the dust bag, push it onto

thedustspoutrmlyasfarasitwillgotopreventitfrom

coming off during operation.

For the best results, empty the dust bag when it

becomes approximately half full, tapping it lightly to

remove as much dust as possible.

OPERATION

Sanding operation

CAUTION: Never run the tool without the

abrasive paper. You may seriously damage the pad.

CAUTION: Never force the tool. Excessive

pressuremaydecreasethesandingefciency,dam-

age the abrasive paper and/or shorten tool life.

►Fig.5

Holdthetoolrmly.Turnthetoolonandwaituntilit

attains full speed. Then gently place the tool on the

workpiecesurface.Anishingsanderisgenerallyused

to remove only a small amount of material at a time.

Since the quality of the surface is more important than

the amount of stock removed, do not bear down on the

tool.Keepthebaseushwiththeworkpieceatalltimes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita M9203 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info