Bedienungsanleitung Makita MT372 (Seite 7 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598765

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Circular work

Circular work may be accomplished if you assemble the

straight guide and guide plate.

Min. and max. radius of circles to be cut (distance

between the centre of circle and the centre of bit) are as

follows:

Min.: 70 mm

Max.: 221 mm

Fig. 15 for cutting circles between 70 mm and

121 mm in radius.

Fig. 16 for cutting circles between 121 mm and

221 mm in radius.

NOTE:

• Circles between 172 mm and 186 mm in radius cannot

be cut using this guide.

Align the centre hole in the straight guide with the centre

of the circle to be cut. Drive a nail less than 6 mm in

diameter into the centre hole to secure the straight guide.

Pivot the tool around the nail in clockwise direction.

(Fig. 17)

Trimmer guide (Fig. 18, 19 & 20)

Trimming, curved cuts in veneers for furniture and the

like can be done easily with the trimmer guide. The guide

roller rides the curve and assures a fine cut.

Attach the chip deflector on the groove of the base. Then

install the trimmer guide and guide holder on the tool

base with the clamping screw (A). Loosen the clamping

screw (B) and adjust the distance between the bit and

the trimmer guide by turning the adjusting screw (1 mm

per turn). At the desired distance, tighten the clamping

screw (B) to secure the trimmer guide in place.

When cutting, move the tool with the guide roller riding

the side of the workpiece.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing carbon brushes (Fig. 21 & 22)

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

NOTE:

• Some items in the list may be included in the tool pack-

age as standard accessories. They may differ from

country to country.

ENG905-1

Noise

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 83 dB (A)

Sound power level (L

): 94 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode : rotation without load

Vibration emission (a

) : 2.5 m/s

or less

Uncertainty (K) : 1.5 m/s

ENG901-1

• The declared vibration emission value has been mea-

sured in accordance with the standard test method and

may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the oper-

ator that are based on an estimation of exposure in the

actual conditions of use (taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to

the trigger time).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita MT372 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info