Bedienungsanleitung Makita MT902 (Seite 9 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598746

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Grinding and sanding operation

ALWAYS hold the tool firmly with one hand on rear han-

dle and the other on the side handle. Turn the tool on and

then apply the wheel or disc to the workpiece.

In general, keep the edge of the wheel or disc at an angle

of about 15 degrees to the workpiece surface.

During the break-in period with a new wheel, do not work

the grinder in the B direction or it will cut into the work-

piece. Once the edge of the wheel has been rounded off

by use, the wheel may be worked in both A and B direc-

tion. (Fig. 8)

Operation with wire cup brush

(optional accessory) (Fig. 9)

CAUTION:

• Check operation of brush by running tool with no load,

insuring that no one is in front of or in line with brush.

• Do not use brush that is damaged, or which is out of

balance. Use of damaged brush could increase poten-

tial for injury from contact with broken brush wires.

Unplug tool and place it upside down allowing easy

access to spindle. Remove any accessories on spindle.

Mount wire cup brush onto spindle and tighten with sup-

plied wrench. When using brush, avoid applying too

much pressure which causes over bending of wires,

leading to premature breakage.

Operation with wire wheel brush

(optional accessory) (Fig. 10)

CAUTION:

• Check operation of wire wheel brush by running tool

with no load, insuring that no one is in front of or in line

with the wire wheel brush.

• Do not use wire wheel brush that is damaged, or which

is out of balance. Use of damaged wire wheel brush

could increase potential for injury from contact with bro-

ken wires.

• ALWAYS use guard with wire wheel brushes, assuring

diameter of wheel fits inside guard. Wheel can shatter

during use and guard helps to reduce chances of per-

sonal injury.

Unplug tool and place it upside down allowing easy

access to spindle. Remove any accessories on spindle.

Thread wire wheel brush onto spindle and tighten with

the wrenches.

When using wire wheel brush, avoid applying too much

pressure which causes over bending of wires, leading to

premature breakage.

Operation with abrasive cut-off / diamond wheel

(optional accessory) (Fig. 11)

WARNING:

• When using an abrasive cut-off / diamond wheel, be

sure to use only the special wheel guard designed for

use with cut-off wheels.

• NEVER use cut-off wheel for side grinding.

• Do not “jam” the wheel or apply excessive pressure. Do

not attempt to make an excessive depth of cut. Over-

stressing the wheel increases the loading and suscepti-

bility to twisting or binding of the wheel in the cut and

the possibility of kickback, wheel breakage and over-

heating of the motor may occur.

• Do not start the cutting operation in the workpiece. Let

the wheel reach full speed and carefully enter into the

cut moving the tool forward over the workpiece surface.

The wheel may bind, walk up or kickback if the power

tool is started in the workpiece.

• During cutting operations, never change the angle of

the wheel. Placing side pressure on the cut-off wheel

(as in grinding) will cause the wheel to crack and break,

causing serious personal injury.

• A diamond wheel shall be operated perpendicular to

the material being cut.

Mount the inner flange onto the spindle. Fit the wheel/

disc on the inner flange and screw the lock nut onto the

spindle.

When installing a diamond wheel or a abrasive cut-off

wheel with its 7 mm or more thick wheel body, mount the

lock nut with its pilot circular part (protrusion) for wheel

bore facing the wheel.

For Australia and New Zealand

Installing or removing abrasive cut-off wheel /

diamond wheel (optional accessory) (Fig. 12)

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

The tool and its air vents have to be kept clean. Regularly

clean the tool’s air vents or whenever the vents start to

become obstructed. (Fig. 13)

Replacing carbon brushes (Fig. 14 & 15)

When the resin insulating tip inside the carbon brush is

exposed to contact the commutator, it will automatically

shut off the motor. When this occurs, both carbon

brushes should be replaced. Keep the carbon brushes

clean and free to slip in the holders. Both carbon brushes

should be replaced at the same time. Use only identical

carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita MT902 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info