Bedienungsanleitung Makita MT903 (Seite 5 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598747

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

ENGLISH (Original instructions)

Explanation of general view

1 Shaft lock

2 Switch trigger

3 Lock lever

4 Wheel guard

5Screw

6 Bearing box

7 Lock nut

8 Depressed center grinding

wheel

9 Inner flange

10 Lock nut wrench

11 Wire cup brush

12 Wire wheel brush

13 Abrasive cut-off wheel/diamond

wheel

14 Wheel guard for abrasive cut-off

wheel/diamond wheel

15 Outer flange 78

16 Inner flange 78

17 Exhaust vent

18 Inhalation vent

19 Commutator

20 Insulating tip

21 Carbon brush

22 Brush holder cap

23 Screwdriver

SPECIFICATIONS

Model MT902 MT903

Depressed center wheel diameter................................................180 mm 230 mm

Spindle thread ..............................................................................M14 M14

Rated speed (n) / No load speed (n

)...........................................8,500 min

-1

6,600 min

-1

Overall length ...............................................................................466 mm 466 mm

Net weight.....................................................................................5.4 kg 5.7 kg

Safety class .................................................................................. /II /II

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

ENE048-1

Intended use

The tool is intended for grinding, sanding and cutting of

metal and stone materials without the use of water.

ENF002-1

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

ENF100-1

For public low-voltage distribution systems of

between 220 V and 250 V.

Switching operations of electric apparatus cause voltage

fluctuations. The operation of this device under unfavor-

able mains conditions can have adverse effects to the

operation of other equipment. With a mains impedance

equal or less than 0.24 Ohms it can be presumed that

there will be no negative effects. The mains socket used

for this device must be protected with a fuse or protective

circuit breaker having slow tripping characteristics.

GEA010-1

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future refer-

ence.

GEB033-3

GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding, Sanding,

Wire Brushing, or Abrasive Cutting-Off Operations:

1. This power tool is intended to function as a

grinder, sander, wire brush or cut-off tool. Read

all safety warnings, instructions, illustrations

and specifications provided with this power tool.

Failure to follow all instructions listed below may

result in electric shock, fire and/or serious injury.

2. Operations such as polishing are not recom-

mended to be performed with this power tool.

Operations for which the power tool was not

designed may create a hazard and cause personal

injury.

3. Do not use accessories which are not specifi-

cally designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories can-

not be adequately guarded or controlled.

6. The arbour size of wheels, flanges, backing pads

or any other accessory must properly fit the

spindle of the power tool. Accessories with arbour

holes that do not match the mounting hardware of

the power tool will run out of balance, vibrate exces-

sively and may cause loss of control.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita MT903 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info