Bedienungsanleitung Makita MT941 (Seite 5 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598741

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing abrasive belt (Fig. 2 & 3)

Pull the lever all the way out and install the belt over the

rollers, and then return the lever to the original position.

CAUTION:

• When installing the belt, make sure that the direction of

the arrow on the back of the belt corresponds to the

one on the tool itself.

Installing or removing step (Fig. 4)

Using step with the tool turned upside down allows sand-

ing another way of use. Remove the knob and then place

the step on the place the knob was seated and secure it

with knob.

Adjusting belt tracking (Fig. 5)

While the belt is running, use the adjusting knob to center

the belt tracking. Failure to do so can result in frayed belt

edges and wear on the sander frame.

Dust bag (Fig. 6)

The use of the dust bag makes sanding operations clean

and dust collection easy. To attach the dust bag, fit it onto

the dust spout.

When the dust bag is about half full, remove the dust bag

from the tool and pull the fastener out. Empty the dust

bag of its contents, tapping it lightly so as to remove par-

ticles adhering to the insides which might hamper further

collection.

OPERATION

Sanding operation (Fig. 7)

CAUTION:

• The tool should not be in contact with the workpiece

surface when you turn the tool on or off. Otherwise a

poor sanding finish or damage of the belt may result.

Hold the tool firmly with both hands. Turn the tool on and

wait until it attains full speed. Then gently place the tool

on the workpiece surface. Keep the belt flush with the

workpiece at all times and move the tool back and forth.

Never force the tool. The weight of the tool applies ade-

quate pressure. Excessive pressure may cause stalling,

overheating of the motor, burning of the workpiece and

possible kickback.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing carbon plate (Fig. 8)

Replace an carbon plate on the cork rubber plate when it

is worn down. Remove screws on the strap washer and

the worn carbon plate, place a new carbon plate and

then secure it with the screws.

Replacing carbon brushes (Fig. 9 & 10)

Remove and check the carbon brushes regularly.

Replace them when they are worn down to the limit

mark. Keep the carbon brushes clean and free to slip in

the holders. Both carbon brushes should be replaced at

the same time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

ENG905-1

Noise

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 87 dB (A)

Sound power level (L

): 98 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: sanding metal plate

Vibration emission (a

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been mea-

sured in accordance with the standard test method and

may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the oper-

ator that are based on an estimation of exposure in the

actual conditions of use (taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to

the trigger time).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita MT941 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info