Bedienungsanleitung Makita MT961 (Seite 8 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598738

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Operation with abrasive cut-off / diamond wheel (optional accessory) (Fig. 8)

The direction for mounting the lock nut and the inner flange varies by wheel thickness.

Refer to the table below.

WARNING:

• When using an abrasive cut-off / diamond wheel, be

sure to use only the special wheel guard designed for

use with cut-off wheels.

• NEVER use cut-off wheel for side grinding.

• Do not “jam” the wheel or apply excessive pressure. Do

not attempt to make an excessive depth of cut. Over-

stressing the wheel increases the loading and suscepti-

bility to twisting or binding of the wheel in the cut and

the possibility of kickback, wheel breakage and over-

heating of the motor may occur.

• Do not start the cutting operation in the workpiece. Let

the wheel reach full speed and carefully enter into the

cut moving the tool forward over the workpiece surface.

The wheel may bind, walk up or kickback if the power

tool is started in the workpiece.

• During cutting operations, never change the angle of

the wheel. Placing side pressure on the cut-off wheel

(as in grinding) will cause the wheel to crack and break,

causing serious personal injury.

• A diamond wheel shall be operated perpendicular to

the material being cut.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing carbon brushes (Fig. 9 & 10)

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

1. Lock nut 2. Abrasive cut-off wheel 3. Inner flange 4. Diamond wheel

Abrasive cut-off wheel

Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more

Diamond wheel

100 mm (4")

Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more

16 mm (5/8") 16 mm (5/8")

20 mm (13/16") 20 mm (13/16")

Abrasive cut-off wheel Diamond wheel

1. Lock nut 2. Abrasive cut-off wheel 3. Inner flange 4. Diamond wheel

115 mm (4 - 1/2") / 125 mm (5")

Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more

22.23 mm (7/8") 22.23 mm (7/8")

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita MT961 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info