Bedienungsanleitung Makita MT963 (Seite 4 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598740

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH (Original instructions)

Explanation of general view

1Press

2 Slide switch lever

3 Wheel guard

4Screw

5 Bearing box

6 Lock nut

7 Depressed center grinding

wheel/ Multi-disc

8 Inner flange

9 Lock nut wrench

10 Shaft lock

11 Abrasive cut-off wheel/

diamond wheel

12 Wheel guard for abrasive cut-off

wheel/diamond wheel

13 Limit mark

14 Brush holder cap

15 Screwdriver

SPECIFICATIONS

Model MT961 MT962 MT963

Wheel diameter......................................................100 mm 115 mm 125 mm

Spindle thread .......................................................M10 x 1.5 M14 x 2 M14 x 2

Rated speed (n) / No load speed (n

) ....................11,000 min

-1

11,000 min

-1

11,000 min

-1

Overall length ........................................................270 mm 270 mm 270 mm

Net weight .............................................................1.9 kg 2.0 kg 2.0 kg

Safety class ........................................................... /II /II /II

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

ENE048-1

Intended use

The tool is intended for grinding, sanding and cutting of

metal and stone materials without the use of water.

ENF002-1

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

GEA010-1

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future refer-

ence.

GEB033-3

GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding, Sanding,

Wire Brushing, or Abrasive Cutting-Off Operations:

1. This power tool is intended to function as a

grinder, sander, wire brush or cut-off tool. Read

all safety warnings, instructions, illustrations

and specifications provided with this power tool.

Failure to follow all instructions listed below may

result in electric shock, fire and/or serious injury.

2. Operations such as polishing are not recom-

mended to be performed with this power tool.

Operations for which the power tool was not

designed may create a hazard and cause personal

injury.

3. Do not use accessories which are not specifi-

cally designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories can-

not be adequately guarded or controlled.

6. The arbour size of wheels, flanges, backing pads

or any other accessory must properly fit the

spindle of the power tool. Accessories with arbour

holes that do not match the mounting hardware of

the power tool will run out of balance, vibrate exces-

sively and may cause loss of control.

7. Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for loose

or cracked wires. If power tool or accessory is

dropped, inspect for damage or install an

undamaged accessory. After inspecting and

installing an accessory, position yourself and

bystanders away from the plane of the rotating

accessory and run the power tool at maximum

no-load speed for one minute. Damaged accesso-

ries will normally break apart during this test time.

8. Wear personal protective equipment. Depending

on application, use face shield, safety goggles

or safety glasses. As appropriate, wear dust

mask, hearing protectors, gloves and workshop

apron capable of stopping small abrasive or

workpiece fragments. The eye protection must be

capable of stopping flying debris generated by vari-

ous operations. The dust mask or respirator must be

capable of filtrating particles generated by your oper-

ation. Prolonged exposure to high intensity noise

may cause hearing loss.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita MT963 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info