448614
5
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
5
ENGLISH
Explanation of general view
SPECIFICATIONS
Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
Specifications may differ from country to country.
Weight according to EPTA-Procedure 01/2003
Intended use
ENE002-1
The tool is intended for planing concrete surfaces.
Power supply
ENF002-1
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety
Warnings GEA010-1
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
CONCRETE PLANER SAW
SAFETY WARNINGS
GEB043-4
Safety Warnings for Grinding Operation:
1. This power tool is intended to function as a
grinder with offset diamond wheels. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
2. Operations such as grinding with abrasive wheels,
sanding, wire brushing, polishing or cutting-off
are not recommended to be performed with this
power tool. Operations for which the power tool was
not designed may create a hazard and cause personal
injury.
3. Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
6. The arbour size of wheels, flanges or any other
accessory must properly fit the spindle of the
power tool. Accessories with arbour holes that do not
match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may cause
loss of control.
7. Do not use a damaged accessory. Before each use
inspect the accessory such as offset diamond
wheels for chips and cracks. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After inspecting
and installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run the power tool at maximum no-
1. Lock lever
2. Switch trigger
3. Indication lamp
4. Base (for PC5001C only)
5. Hex wrench
6. Front roller
7. Hex socket head bolt
8. Stock removal amount
9. Base
10. Same level
11. Square or ruler
12. Raise
13. Lower
14. Dust cover
15. Screw
16. Lock nut
17. Lock nut wrench
18. Diamond wheel
19. Shaft lock
20. Dust bag
21. Dust cover cap
22. The whole roller holder
23. Hex bolt
24. Limit mark
25. Brush holder cap
26. Screwdriver
Model PC5000C PC5001C
Wheel diameter 125 mm
Hole diameter 22.23 mm
Spindle thread M14
Rated speed (n) / No load speed (
n
0
) 10,000 min
-1
Overall length 437 mm 479 mm
Net weight 4.0 kg 5.1 kg
Safety class /II
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita PC 5000C wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info