Bedienungsanleitung Makita PC5010C (Seite 12 von 28) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691508

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

12 ENGLISH

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and unplugged before carrying out

any work on the tool.

Installing or removing loop handle

CAUTION: Always be sure that the loop han-

dle is installed securely before operation.

To install the loop handle, put it onto the tool as illus-

trated and install the bolts. Then tighten them securely

with a hex wrench.

The loop handle can be installed only in the direction as

shown in the gure.

► Fig.5: 1. Loop handle 2. Bolt

To remove the loop handle, follow the above installing

procedure in reverse.

Installing or removing dust

collecting wheel guard

WARNING:

Always switch OFF and unplug the

tool before attaching dust collecting wheel guard.

WARNING:

Dust collecting wheel guard is

only for use in planing concrete surface with a off-

set diamond wheel. Do not use this guard with any

other cutting accessory or for any other purpose.

WARNING: Inspect dust collecting wheel

guard thoroughly before use to ensure that it is

not damaged, cracked and/or deformed.

Remove any abrasive wheel and wheel cover from the tool.

Loosen the screw on dust collecting wheel guard until

attaching slot opens.

► Fig.6: 1. Screw 2. Dust collecting wheel guard

Mount dust collecting wheel guard with the protrusion

on the dust collecting wheel guard aligned with the

notch on the bearing box.

► Fig.7: 1. Dust collecting wheel guard 2. Bearing box

3. Protrusion 4. Notch

Turn the dust collecting wheel guard in direction of the

arrow. Be sure to tighten the screw securely.

► Fig.8: 1. Screw

To remove the dust collecting wheel guard, follow the

above installing procedure in reverse.

Installing or removing offset

diamond wheel

Optional accessory

WARNING: For offset diamond wheels that

are 4 mm or thinner, place the convex section of

the lock nut upwards and attach to the spindle.

WARNING: Be sure to use a genuine Makita

offset diamond wheel.

CAUTION: When installing a diamond wheel,

always make sure to tighten the lock nut rmly.

Mount the inner ange onto the spindle.

Make sure to t the dented part of the inner ange onto

the straight part at the bottom of the spindle.

Fit the offset diamond wheel on the inner ange and

screw the lock nut onto the spindle.

To tighten the lock nut, press the shaft lock rmly so

that the spindle cannot revolve, then use the lock nut

wrench and securely tighten clockwise.

To remove the wheel, follow the above installing proce-

dure in reverse.

► Fig.9:

1. Lock nut 2. Convex section 3. Offset diamond

wheel 4. Inner ange 5. Spindle 6. Shaft lock

Connecting a vacuum cleaner

Optional accessory

► Fig.10

When you wish to perform clean concrete-planing

operation, connect a Makita vacuum cleaner to your

tool. Then connect a hose of the vacuum cleaner to the

nozzle as shown in the gures.

Installing or removing dust cover

attachment

Optional accessory

WARNING: Always be sure that the tool is

switched off and unplugged before installing or

removing the dust cover attachment. Failure to do

so causes damage to the tool or a personal injury.

There are four pieces of dust cover attachment and

each is used in one of different positions.

► Fig.11: 1. Marking A 2. Marking B 3. Marking C

4. Marking D

Set the dust cover attachment so that the marking (A, B, C or

D) places as shown in the gure. Snap its pins in the vents.

Dust cover attachment can be removed by hand.

NOTE: Clean out the dust cover attachment when it

is clogged with dust or foreign matters. Continuing

operation with a clogged dust cover attachment will

damage the tool.

OPERATION

Concrete planing operation

CAUTION: ALWAYS hold the tool rmly with

one hand on the housing and the other on the

auxiliary handle as shown in the gure.

CAUTION:

Before operation, make sure that a

vacuum cleaner is connected to the tool and turned on.

CAUTION: Do not use the tool with damaged

brush. Use of damaged brush could lead to injury by

leaking dust.

Always install the auxiliary handle on the tool before

operation. Hold the tool's switch handle and the auxil-

iary handle rmly with both hands during operation.

► Fig.12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita PC5010C Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info