Bedienungsanleitung Makita PC5010C (Seite 15 von 28) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691508

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

15 ENGLISH

Operation with wire wheel brush

Optional accessory

CAUTION: Check operation of wire wheel

brush by running tool with no load, insuring that

no one is in front of or in line with the wire wheel

brush.

CAUTION: Do not use wire wheel brush that

is damaged, or which is out of balance. Use of

damaged wire wheel brush could increase potential

for injury from contact with broken wires.

CAUTION: ALWAYS use guard with wire

wheel brushes, assuring diameter of wheel ts

inside guard. Wheel can shatter during use and

guard helps to reduce chances of personal injury.

► Fig.30: 1. Wire wheel brush

Unplug tool and place it upside down allowing easy

access to spindle.

Remove any accessories on spindle. Thread wire wheel

brush onto spindle and tighten with the wrenches.

NOTICE: Avoid applying too much pressure

which causes over bending of wires when

using wire wheel brush. It may lead to premature

breakage.

Operation with abrasive cut-off /

diamond wheel

Optional accessory

WARNING: When using an abrasive cut-off

/ diamond wheel, be sure to use only the special

wheel guard designed for use with cut-off wheels.

(In some European countries, when using a diamond

wheel, the ordinary guard can be used. Follow the

regulations in your country.)

WARNING: NEVER use cut-off wheel for side

grinding.

WARNING: Do not "jam" the wheel or apply

excessive pressure. Do not attempt to make an

excessive depth of cut. Overstressing the wheel

increases the loading and susceptibility to twisting

or binding of the wheel in the cut and the possibility

of kickback, wheel breakage and overheating of the

motor may occur.

WARNING: Do not start the cutting operation

in the workpiece. Let the wheel reach full speed

and carefully enter into the cut moving the tool

forward over the workpiece surface. The wheel

may bind, walk up or kickback if the power tool is

started in the workpiece.

WARNING: During cutting operations, never

change the angle of the wheel. Placing side pres-

sure on the cut-off wheel (as in grinding) will cause

the wheel to crack and break, causing serious per-

sonal injury.

WARNING: A diamond wheel shall be oper-

ated perpendicular to the material being cut.

► Fig.31: 1. Lock nut 2. Abrasive cut-off wheel / dia-

mond wheel 3. Inner ange 4. Wheel guard

for abrasive cut-off wheel / diamond wheel

As for the installation, follow the instructions for

depressed center wheel.

The direction for mounting the lock nut and the

inner ange varies by wheel type and thickness.

Refer to the following gures.

When installing the abrasive cut-off wheel:

► Fig.32: 1. Lock nut 2. Abrasive cut-off wheel

(Thinner than 4 mm (5/32")) 3. Abrasive cut-

off wheel (4 mm (5/32") or thicker) 4. Inner

ange

When installing the diamond wheel:

► Fig.33: 1. Lock nut 2. Diamond wheel (Thinner than

4 mm (5/32″)) 3. Diamond wheel (4 mm

(5/32″) or thicker) 4. Inner ange

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and unplugged before attempting to

perform inspection or maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized or Factory Service Centers, always

using Makita replacement parts.

Replacing dust cover brush

Worn brushes can be replaced. To remove the brushes,

pull them off by using slotted driver or other appropriate

tool.

► Fig.34: 1. Brush (large) 2. Brush (small)

Inserting new brushes into retaining grooves by pushing

down from above.

► Fig.35

At this time, ensure that brushes are fully hooked onto

hooks on outer edges of grooves.

► Fig.36: 1. Hook

Air vent cleaning

The tool and its air vents have to be kept clean.

Regularly clean the tool's air vents or whenever the

vents start to become obstructed.

► Fig.37: 1. Exhaust vent 2. Inhalation vent

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita PC5010C Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info