Bedienungsanleitung Makita PJ7000 (Seite 8 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598964

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

OPERATION

How to make joints

WARNING:

• Always clamp the workpiece to the workbench before

each operation. (Fig. 11 & 12)

Corner Joint (Fig. 13, 14 & 15)

T-Butt Joint (Fig. 16, 17 & 18)

Miter Joint (Fig. 19 & 20)

Frame Joint (Fig. 21 & 22)

Edge-To-Edge Joint (Fig. 23 & 24)

To make joints, proceed as follows:

1. Fit the two workpieces together as they will appear

in the finished joint position.

2. Mark the center of the intended biscuit grooves on

the workpiece using a pencil.

NOTE:

• The center of grooves should be at least 50 mm from

the outer edge of the workpieces.

• Allow 100 mm – 150 mm between grooves in multiple

biscuit application.

3. For Corner Joint and T-Butt Joint only

Clamp the vertical workpiece to the workbench.

For Miter Joint only

Clamp one workpiece to the workbench with the

mitered edge facing up.

For Frame Joint and Edge-To-Edge Joint only

Clamp one workpiece to the workbench.

4. Set the depth of groove according to the size of bis-

cuit to be used. Refer to the table in the “Adjusting

the depth of groove” section.

5. Adjust the angle guide height so that the blade is

centered in the board thickness.

6. Align the center mark on the base with the pencil

line on the workpiece.

7. Switch on the tool and gently push it forward to

extend the blade into the workpiece.

8. Gently return the tool to the original position after the

adjusting screw reaches the stopper.

9. For Corner Joint and T-Butt Joint only

Clamp the horizontal workpiece to the workbench.

For Miter Joint only

Clamp the other workpiece to the workbench with

the mitered edge facing up.

For Frame Joint and Edge-To-Edge Joint only

Clamp the other workpiece to the workbench.

10. For Corner Joint only

Place the tool on the workpiece so that the blade is

facing down.

For T-Butt Joint only

Remove the angle guide from the tool. Place the tool

on the workpiece so that the blade is facing down.

11. Repeat the steps 6 – 8 to groove in the horizontal or

the other workpiece.

If you do not need to center the blade in the board thick-

ness, proceed as follows:

For Corner Joint, Miter Joint, Frame Joint and Edge-

To-Edge Joint only

• Remove the angle guide from the tool. Set the fence at

90° for Corner Joint, Frame Joint and Edge-To-Edge

Joint or at 45° for Miter Joint.

• Follow steps 1 – 11 excluding steps 5 and 10 described

above.

For T-Butt Joint only

• Fit the two workpieces together as they will appear in

the finished joint position.

• Lay the vertical workpiece on the horizontal one. Clamp

both workpieces to the workbench.

• Remove the angle guide from the tool.

• Follow the steps 2, 4, 6, 7, 8 and 11 described above.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

The tool and its air vents have to be kept clean. Regularly

clean the tool’s air vents or whenever the vents start to

become obstructed. (Fig. 25)

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Angle guide

• Dust bag

• Set plate 4

• Lock nut wrench 20

• Plate joiner blades

NOTE:

• Some items in the list may be included in the tool pack-

age as standard accessories. They may differ from

country to country.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita PJ7000 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info