Bedienungsanleitung Makita PLM 4600 (Seite 19 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78718

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

STANDARDS OF USE

For instructions regarding the engine and the battery (if

supplied), read the relevant manuals.

NOTE – The machine can be supplied with some of the

components already fitted.

Return the lower part of the handle, which is made

up of two pre-assembled elements (1), to its working posi-

tion and lock into place using the lower knobs (2). Attach

the upper part (3) using the screws (4) supplied, ensuring

that the spiral (5) of the starter cable is in the correct posi-

tion.Attach the control cables using the clips (6). By loos-

ening the knobs (2) the handle can be set at three different

heights.

Assemble the dashboard (1) following the steps

shown.

With the plastic part (11) upside-down, fasten the

frame (12) to the plastic part using the screws (13).

Insert the frame (12) into the sack (14) and attach the plas-

tic profile (15) with the help of a screwdriver, as shown in

the drawing.

Fit the edge of the cloth (16) right into the groove of the

plastic part (11), starting 5-7 mm from the ends.

The throttle (where fitted) is controlled by the lever

(1) and positioned as shown on the relative plate. Some

models have a fixed speed, and therefore no need of a

throttle (2).

The blade brake is controlled by the lever (1), which

should be held against the handle when starting and using

the lawnmower.The engine stops when the lever is

released.

In power-driven models, draw the lever (1) towards

the handle for forward movement. The lawnmower stops

moving forward when the lever is released.

The cutting height is adjusted using the levers (1).

The four wheels must be at the same height.

MAKE THIS ADJUSTMENT ONLY WHEN THE BLADE HAS

STOPPED MOVING.

The speed changer (if fitted) is controlled by moving

the lever to one of the four positions, marked as:

1 - 2 - 3 - 4

The move from one speed to another must be made with

the engine running and drive engaged.

IMPORTANT - Do not touch the speed changer when the

engine is stopped. This operation could damage the speed

changer.

NOTE - If the machine does not move forwards with the

control in position «1», it is enough to move the control to

«4» and then immediately return it to position «1».

Lift the stone-guard and attach the grass-catcher

(1) correctly as shown in the drawing.

3.1

3. GRASS CUTTING

2.5

2.4

2.3

2.2

2.1

2. DESCRIPTION OF CONTROLS

1.3

1.2

1.1

1. FINISH ASSEMBLY

To start the engine, follow the instructions in the

engine booklet and then pull the blade brake lever (1)

towards the handle and give a sharp pull on the starter

cable knob (2).

The lawn will look better if it is always cut to the

same height and in alternate directions.

When you have finishing mowing, release the brake

lever (1) and disconnect the spark plug cap (2).

WAIT FOR THE BLADE TO STOP before carrying out any

type of work on the machine.

IMPORTANT – Regular, careful maintenance is essen-

tial for keeping the safety level and original perform-

ance of the machine unchanged in time.

Store the lawnmower in a dry place.

1) Wear strong working gloves during any cleaning, main-

tenance or adjustment operation on the machine.

2) Carefully clean the machines with water after each cut;

remove the grass debris and mud accumulated inside

the chassis to avoid their drying and thus making the

next start-up difficult.

3) The paintwork on the inside of the chassis may peel off

in time due to the abrasive action of the cut grass; in this

case, intervene promptly by touching up the paintwork

using a rustproof paint to prevent the formation of rust

that would lead to corrosion of the metal.

4) Should it be necessary to access the lower part, only tilt

the machine from the side shown in the engine hand-

book; following the relative instructions.

5) Do not drip petrol onto the plastic parts of the motor or

the machine to prevent damaging them and remove all

traces of spilt petrol immediately. The warranty does not

cover damage to plastic parts caused by petrol.

All operations on the blade should be carried out at

a specialized centre.

Note for specialized centres: Reassemble the blade (2) as

shown in the drawing and tighten the central screw (1)

using a torque wrench set to 35-40 Nm.

In power-driven models:

• adjust the tension of the belt with the nut (1) to get the

right measurement (6 mm).

• turn the adjusting nut (2) so that the wire (3) is slightly

loose and the lever (4) is idle.

The control cable must be adjusted if the difference

in speed between position «2» and position «4» is minimal

or nil.

NOTE - The adjustment must be made with the engine

switched off.

Gradually turn register (2)

anticlockwise (so as to cause it

to extend) until control lever (1) has difficulty in reaching

position «4»; at this point turn the register

clockwise by

about half a turn, to obtain optimal adjustment of the for-

ward speed, together with correct engagement of the four

speeds using control lever (1).

Should you have any doubts or problems, do not hesitate

to contact your nearest Service Centre or your Dealer.

4.3

4.2

4.1

4. ROUTINE MAINTENANCE

3.4

3.3

3.2

Makita PLM 4600 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info