Bedienungsanleitung Makita PT354D (Seite 7 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691774

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

7 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge.Failuretoholdthetoolandthebattery

cartridgermlymaycausethemtoslipoffyourhands

andresultindamagetothetoolandbatterycartridge

andapersonalinjury.

►Fig.1: 1. Red indicator 2. Button 3. Battery cartridge

Toremovethebatterycartridge,slideitfromthetool

whileslidingthebuttononthefrontofthecartridge.

Toinstallthebatterycartridge,alignthetongueonthe

batterycartridgewiththegrooveinthehousingandslip

it into place. Insert it all the way until it locks in place

withalittleclick.Ifyoucanseetheredindicatoronthe

uppersideofthebutton,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen.Ifnot,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly.Ifthecartridgedoesnotslideineasily,itis

notbeinginsertedcorrectly.

Battery protection system

Thetoolisequippedwithabatteryprotectionsystem.

Thissystemautomaticallycutsoffpowertothemotorto

extendbatterylife.

Thetoolwillautomaticallystopduringoperationifthe

tooland/orbatteryareplacedunderoneofthefollowing

conditions:

Overloaded:

Thetoolisoperatedinamannerthatcausesittodraw

anabnormallyhighcurrent.

Inthissituation,turnthetooloffandstoptheapplication

thatcausedthetooltobecomeoverloaded.Thenturn

the tool on to restart.

Ifthetooldoesnotstart,thebatteryisoverheated.In

thissituation,letthebatterycoolbeforeturningthetool

on again.

Low battery voltage:

Theremainingbatterycapacityistoolowandthetool

willnotoperate.Ifyouturnthetoolon,themotordoes

notrunorthemotorrunsagainbutstopssoon.Inthis

situation,removeandrechargethebattery.

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

►Fig.2: 1. Indicator lamps 2.Checkbutton

Pressthecheckbuttononthebatterycartridgetoindi-

catetheremainingbatterycapacity.Theindicatorlamps

lightupforfewseconds.

Indicator lamps Remaining

capacity

Lighted Off

75%to100%

50%to75%

25%to50%

0%to25%

NOTE:Dependingontheconditionsofuseandthe

ambienttemperature,theindicationmaydifferslightly

fromtheactualcapacity.

Trigger-lock button

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

CAUTION: When not operating the tool,

depress the trigger-lock button from B side to

lock the switch trigger in the OFF position.

►Fig.3: 1.Trigger-lockbutton2.Switchtrigger

►Fig.4

Topreventtheswitchtriggerfromaccidentallypulled,

thetrigger-lockbuttonisprovided.

Topulltheswitchtrigger,depressthetrigger-lockbutton

fromAside.

Afteruse,alwayspressinthetrigger-lockbuttonfrom

B side.

Adjusting the depth of pin-nailing

WARNING: Always make sure that your

ngers are not placed on the switch trigger or

the contact element and the battery cartridge is

removed before adjusting the depth of nailing.

Depthofpin-nailingcanbeadjustedonthispinnailer.

Toadjustthedepthofnailing,turntheadjuster.The

depthofnailingisthedeepestwhentheadjusteris

turnedfullyintheAdirectionshowninthegure.It

willbecomeshallowerastheadjusteristurnedin

theBdirection.Depthcanbeadjusted1.5mmtothe

maximum.

►Fig.5: 1.Adjuster

►Fig.6: 1.Toodeep2. Flush 3.Tooshallow

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita PT354D Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info