Bedienungsanleitung Makita PTR2500 (Seite 16 von 98) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

598974

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

Adding grease and lubricant

- The gearbox of the pole hedge trimmer should be greased every 20 working

hours. Add approx. 10cc of lubricant (Shell Alvania No. 3 or equivalent) to the

gearbox via the grease nipples. (Some grease will emerge from the head of the

gearbox (located at the base of the blade) when the pole hedge trimmer is set in

motion the first time after greasing. Use this as a rough indicator for the amount

of grease to supply.)

Note: Observe greasing intervals and the amount of grease to be supplied.

Mechanical parts of the pole hedge trimmer may be damaged if grease is

not supplied at the prescribed intervals or if an insufficient amount of

grease is added.

Fuel tank filter

- The inside of the fuel tank is equipped with a filter (1) that cleans the fuel before

it enters the carburetor.

- Visually check the filter at regular intervals. To do so, use a piece of wire formed

into a hook and draw the filter out of the tank (2). Replace the filter if it is

hardened, clogged up, or excessively contaminated.

- Inadequate fuel supply as a result of a deteriorated fuel filter may result in poor

engine performance. In order to ensure that the required amount of fuel enters

the carburetor, replace the fuel filter whenever in doubt of its condition.

Cleaning the muffler outlet

- Check the condition of the muffler outlet (3) at regular intervals.

- Use a suitable tool to remove excessive carbon residue that accumulates

around the muffler outlet. Take special care to prevent removed carbon residue

from entering engine parts.

Cleaning the spark arrester

- The spark arrester should be cleaned every 50 working hours.

- Have the spark arrester cleaned at your dealership or by an authorized service

agent.

For all maintenance work not mentioned in this instruction manual, please contact

your dealership or an authorized service agent.

Daily inspection and maintenance

To ensure a long service life of your pole hedge trimmer, perform the following

inspections and maintenance on a daily basis.

- Always check for loose or missing parts before starting operation. Pay special

attention to the cutting unit and make sure that the cutter blade lock screws are

well tightened.

- Check for clogging of the cooling air passages and the cooling fins of the

cylinder before starting operation. Clean if necessary.

- Each day after using the pole hedge trimmer perform the following.

• Clean the outside of the pole hedge trimmer; check for damage and loose

parts.

• Clean the air filter. Clean the filter several times a day if working in extremely

dusty conditions.

• Check the cutter blades for damage. Make sure that the blades are securely

mounted.

Grease nipple

(1)

(3)

(2)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita PTR2500 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info