Bedienungsanleitung Makita rp 1110 c (Seite 6 von 10) (Englisch, Holländisch)

426965

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

OPERATING INSTRUCTIONS

Installing or removing router bit

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

Loosen the collet nut. Insert the bit all the way into the

collet cone. Press the shaft lock to keep the shaft station-

ary and use the wrench to tighten the collet nut securely.

(Fig.1)

A 8 mm or 1/4” collet cone is factory installed on the tool.

When using router bits with other shank diameter, use

the correct size collet cone for the bit which you intended

to use. (Fig.2)

Optional accessories include 6 mm, 8 mm and 1/4" collet

cones.

To remove the bit, follow the installation procedure in

reverse.

CAUTION:

Do not tighten the collet nut without inserting a bit, or the

collet cone will break.

Adjusting the depth of cut (Fig. 3)

Place the tool on a flat surface.

Loosen the lock knob and lower the tool body until the bit

just touches the flat surface. Tighten the lock knob to lock

the tool body.

Turn the stopper pole setting nut counterclockwise.

Lower the stopper pole until it makes contact with the

adjusting bolt. Align the depth pointer with the “0” gradua-

tion. The depth of cut is indicated on the scale by the

depth pointer.

While pressing the fast-feed button, raise the stopper

pole until the desired depth of cut is obtained. Minute

depth adjustments can be obtained by turning the adjust-

ing knob (1mm per turn.)

By turning the stopper pole setting nut clockwise, you

can fasten the stopper pole firmly.

Now, your predetermined depth of cut can be obtained by

loosening the lock knob and then lowering the tool body

until the stopper pole makes contact with the adjusting

bolt of the stopper block.

Nylon nut (Fig. 4)

CAUTION:

• Do not lower the nylon nut too low or the bit will pro-

trude dangerously.

By turning the nylon nut, the upper limit of the tool body

can be adjusted. When the tip of the bit is retracted more

than required in relation to the base plate surface, turn

the nylon nut to lower the upper limit.

CAUTION:

• Since excessive cutting may cause overload of the

motor or difficulty in controlling the tool, the depth of cut

should not be more than 15 mm at a pass when cutting

grooves with an 8 mm diameter bit.

• When cutting grooves with a 20 mm diameter bit, the

depth of cut should not be more than 5 mm at a pass.

• For extra-deep grooving operations, make two or three

passes with progressively deeper bit settings.

Stopper block (Fig. 5)

The stopper block has three adjusting hex bolts which

raise or lower 0.8 mm per turn. You can easily obtain

three different depths of cut using these adjusting hex

bolts without readjusting the stopper pole.

Adjust the lowest hex bolt to obtain the deepest depth of

cut. Adjust the two remaining hex bolts to obtain shal-

lower depths of cut. The differences in height of these

hex bolts are equal to the differences in depths of cut. To

adjust the hex bolts, first loosen the hex nuts on the hex

bolts with the wrench and then turn the hex bolts. After

obtaining the desired position, tighten the hex nuts while

holding the hex bolts in that desired position. The stopper

block is also convenient for making three passes with

progressively deeper bit settings when cutting deep

grooves.

Switch action (Fig.6)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

• Make sure that the shaft lock is released before the

switch is turned on.

To start the tool, depress the lock button and pull the

switch trigger. Release the switch trigger to stop. For con-

tinuous operation, pull the trigger and then depress the

lock button further.

To stop the tool, pull the trigger so that the lock-off button

returns automatically. Then release the trigger. After

releasing the trigger, the lock-off function works to pre-

vent the switch trigger from being pulled.

Speed adjusting dial (Fig. 7)

For RP1110C

The tool speed can be infinitely adjusted between 8,000

and 24,000 min

-1

by turning the speed adjusting dial.

This allows the ideal speed to be selected for optimum

material processing, i.e. the speed can be correctly

adjusted to suit the material and bit diameter.

Refer to the table below for the relationship between the

number settings on the dial and the approximate rotating

speed.

CAUTION:

The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

Number min

-1

18,000

2 12,000

3 16,000

4 20,000

5 24,000

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita rp 1110 c Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita rp 1110 c

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info