Bedienungsanleitung Makita rp 1110 c (Seite 5 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

426965

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ENGLISH (Original instructions)

Explanation of general view

1 Adjusting knob

2 Stopper pole

3 Depth pointer

4 Stopper pole setting nut

5 Lock knob

6 Fast-feed button

7 Adjusting hex bolt

8 Stopper block

9 Nylon nut

10 Hex nut

11 Lock button

12 Switch trigger

13 Speed adjusting dial

14 Collet nut

15 Wrench

16 Shaft lock

17 Tighten

18 Loosen

19 Correct size collet cone

20 Workpiece

21 Bit revolving direction

22 Feed direction

23 View from the top of the tool

24 Straight guide

25 Lock screw

26 Guiding surface

27 Templet guide

28 Screw

29 Bit

30 Base

31 Templet

32 Workpiece

33 Distance (X)

34 Outside diameter of the templet

guide

35 Nozzle assembly

36 Dust nozzle assembly

37 Limit mark

38 Brush holder cap

39 Screwdriver

SPECIFICATIONS

Model RP0910 RP1110C

Max. collet capacity ..................................................................... 8 mm or 1/4” 8 mm or 1/4”

Plunge capacity ........................................................................... 0 – 57mm 0 – 57 mm

No load speed (min

–1

) ................................................................. 27,000 8,000 – 24,000

Overall height .............................................................................. 260 mm 260 mm

Net weight .................................................................................... 3.3 kg 3.4 kg

Safety class ................................................................................. /II /II

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

Intended use

The tool is intended for flush trimming and profiling of

wood, plastic and similar materials.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

GEA010-1

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future refer-

ence.

GEB018-2

ROUTER SAFETY WARNINGS

1. Hold power tool by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. Use clamps or another practical way to secure

and support the workpiece to a stable platform.

Holding the work by hand or against your body

leaves it unstable and may lead to loss of control.

3. Wear hearing protection during extended period

of operation.

4. Handle the bits very carefully.

5. Check the bit carefully for cracks or damage

before operation. Replace cracked or damaged

bit immediately.

6. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

7. Hold the tool firmly with both hands.

8. Keep hands away from rotating parts.

9. Make sure the bit is not contacting the work-

piece before the switch is turned on.

10. Before using the tool on an actual workpiece, let

it run for a while. Watch for vibration or wobbling

that could indicate improperly installed bit.

11. Be careful of the bit rotating direction and the

feed direction.

12. Do not leave the tool running. Operate the tool

only when hand-held.

13. Always switch off and wait for the bit to come to

a complete stop before removing the tool from

workpiece.

14. Do not touch the bit immediately after operation;

it may be extremely hot and could burn your

skin.

15. Do not smear the tool base carelessly with thin-

ner, gasoline, oil or the like. They may cause

cracks in the tool base.

16. Draw attention to the need to use cutters of the

correct shank diameter and which are suitable

for the speed of the tool.

17. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation

and skin contact. Follow material supplier safety

data.

18. Always use the correct dust mask/respirator for

the material and application you are working

with.

SAVE THESE INSTRUCTIONS.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita rp 1110 c Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita rp 1110 c

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info