Bedienungsanleitung Makita sa 7000 c (Seite 6 von 14) (Englisch, Holländisch)

391187

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Speed adjusting dial (Fig. 3)

The rotating speed can be changed by turning the speed

adjusting dial to a given number setting from 1 to 6 (6 at

the time when the switch trigger is fully pulled).

Higher speed is obtained when the dial is turned in the

direction of number 6. And lower speed is obtained when

it is turned in the direction of number 1.

Refer to the table for the relationship between the num-

ber settings on the dial and the approximate rotating

speed.

CAUTION:

• The speed adjusting dial can be turned only as far as 6

and back to 1. Do not force it past 6 or 1, or the speed

adjusting function may no longer work.

• If the tool is operated continuously at low speeds, the

motor will get overloaded and heated up.

Electronic function

The tools equipped with electronic function are easy to

operate because of the following features.

Constant speed control

Possible to get fine finish, because the rotating speed is

kept constant even under loaded condition.

Additionally, when the load on the tool exceeds admissi-

ble levels, power to the motor is reduced to protect the

motor from overheating. When the load returns to admis-

sible levels, the tool will operate as normal.

Soft start feature

Soft start because of suppressed starting shock.

ASSEMBLY

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing side grip (handle) (Fig. 4 & 5)

CAUTION:

Always be sure that the side grip is installed securely

before operation.

Remove one of the screws which secure gear housing

and head cover, then screw the side grip on the tool.

Installing or removing abrasive disc (Fig. 6 & 7)

NOTE:

Use sander accessories specified in this manual. These

must be purchased separately.

Mount the rubber pad onto the spindle. Fit the disc on the

rubber pad and screw the lock nut onto the spindle. To

tighten the lock nut, press the shaft lock firmly so that the

spindle cannot revolve, then use the lock nut wrench and

securely tighten clockwise.

To remove the disc, follow the installation procedure in

reverse.

OPERATION

WARNING:

• It should never be necessary to force the tool. The

weight of the tool applies adequate pressure. Forcing

and excessive pressure could cause dangerous wheel

breakage.

CAUTION:

• Never switch on the tool when it is in contact with the

workpiece, it may cause an injury to operator.

• Never run the tool without the abrasive disc. You may

seriously damage the pad.

• Always wear safety goggles or a face shield during

operation.

• After operation, always switch off the tool and wait until

the disc has come to a complete stop before putting the

tool down.

ALWAYS hold the tool firmly with one hand on rear han-

dle and the other on the side handle. Turn the tool on and

then apply the abrasive disc to the workpiece.

In general, keep the abrasive disc at an angle of about

15 degrees to the workpiece surface. (Fig. 8)

Apply slight pressure only. Excessive pressure will result

in poor performance and premature wear to abrasive

disc.

Number min

-1

(R.P.M.)

11,500

21,700

32,000

42,500

53,300

64,000

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita sa 7000 c Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita sa 7000 c

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info