Bedienungsanleitung Makita SA7000 (Seite 5 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598934

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

10. Hold power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or

its own cord. Cutting accessory contacting a "live"

wire may make exposed metal parts of the power

tool "live" and shock the operator.

11. Position the cord clear of the spinning acces-

sory. If you lose control, the cord may be cut or

snagged and your hand or arm may be pulled into

the spinning accessory.

12. Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

accessory may grab the surface and pull the power

tool out of your control.

13. Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

14. Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may

cause electrical hazards.

15. Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

16. Do not use accessories that require liquid cool-

ants. Using water or other liquid coolants may result

in electrocution or shock.

17. Kickback and Related Warnings

Kickback is a sudden reaction to a snagged rotating

backing pad or any other accessory. Snagging

causes rapid stalling of the rotating accessory which

in turn causes the uncontrolled power tool to be

forced in the direction opposite of the accessory’s

rotation at the point of the binding. Kickback is the

result of power tool misuse and/or incorrect operat-

ing procedures or conditions and can be avoided by

taking proper precautions as given below.

a) Maintain a firm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use auxiliary

handle, if provided, for maximum control

over kickback or torque reaction during start-

up. The operator can control torque reactions or

kickback forces, if proper precautions are taken.

b) Never place your hand near the rotating

accessory. Accessory may kickback over your

hand.

c) Do not position your body in the area where

power tool will move if kickback occurs. Kick-

back will propel the tool in direction opposite to

the wheel’s movement at the point of snagging.

d) Use special care when working corners,

sharp edges etc. Avoid bouncing and snag-

ging the accessory. Corners, sharp edges or

bouncing have a tendency to snag the rotating

accessory and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade

or toothed saw blade. Such blades create fre-

quent kickback and loss of control.

Safety Warnings Specific for Sanding Operations:

18. Do not use excessively oversized sanding disc

paper. Follow manufacturers recommenda-

tions, when selecting sanding paper. Larger

sanding paper extending beyond the sanding pad

presents a laceration hazard and may cause snag-

ging, tearing of the disc or kickback.

19. Accessories must be rated for at least the speed

recommended on the tool warning label. Wheels

and other accessories running over rated speed can

fly apart and cause injury. Maximum operating

speed of accessories should be higher than the

highest no load speed marked on the tool’s name-

plate.

20. Always use safety glasses or goggles. Ordinary

eye or sun glasses are NOT safety glasses.

21. Check the backing pad carefully for cracks, dam-

age or deformity before operation. Replace

cracked, damaged or deformed pad immediately.

22. NEVER use tool with wood cutting blades or

other sawblades. Such blades when used on a

sander frequently kick and cause loss of control

leading to personal injury.

23. Hold the tool firmly.

24. Keep hands away from rotating parts.

25. Make sure the abrasive disc is not contacting the

workpiece before the switch is turned on.

26. When sanding metal surfaces, watch out for fly-

ing sparks. Hold the tool so that sparks fly away

from you and other persons or flammable mate-

rials.

27. Do not leave the tool running. Operate the tool

only when hand-held.

28. Do not touch the workpiece immediately after

operation; it may be extremely hot and could

burn your skin.

29. Check that the workpiece is properly supported.

30. Pay attention that the wheel continues to rotate

after the tool is switched off.

31. This tool has not been waterproofed, so do not

use water on the workpiece surface.

32. Ventilate your work area adequately when you

perform sanding operations.

33. Use of this tool to sand some products, paints

and wood could expose user to dust containing

hazardous substances. Use appropriate respira-

tory protection.

34. Always use eye and ear protection. Other per-

sonal protective equipment such as dust mask,

gloves, helmet and apron should be worn.

35. Always be sure that the tool is switched off and

unplugged before carrying out any work on the

tool.

36. If working place is extremely hot and humid, or

badly polluted by conductive dust, use a short-

circuit breaker (30 mA) to assure operator safety.

37. Do not use the tool on any materials containing

asbestos.

38. Do not use water or grinding lubricant.

39. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation

and skin contact. Follow material supplier safety

data.

40. Always use the correct dust mask/respirator for

the material and application you are working

with.

41. Ensure that ventilation openings are kept clear

when working in dusty conditions. If it should

become necessary to clear dust, first disconnect

the tool from the mains supply (use non metallic

objects) and avoid damaging internal parts.

SAVE THESE INSTRUCTIONS.

Makita SA7000 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info