Bedienungsanleitung Makita SC 190DW (Seite 10 von 16) (Englisch, Holländisch)

448644

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Replace the cutters in accordance with the following procedure. Use only Makita genuine cutters for the tool.

1. There are two cutters. Cutter A is to be installed on the cutter head, and cutter B on the cutter rod. Be sure

to install them in the correct respective position. Refer to the table below for the cutter sizes.

For Model Cutter A Cutter B

SC130DRA

20x15x9mm

(four cutting edges)

20x15x8mm

(four cutting edges)

SC160DRA

22x17x9mm

(four cutting edges)

22x17x8mm

(one cutting edge)

SC190DW

28x20x11.5mm

(four cutting edges)

26x20x10mm

(four cutting edges)

2. To install the cutters, first remove the two hex socket head bolts holding the cutters on the cutter head and

cutter rod, respectively.

3. Wipe off any dirt or foreign matter from the cutter-mounting position on the cutter head and cutter rod.

4. Secure firmly cutter A on the cutter head and cutter B on the cutter rod, using their respective flat washers

and hex socket head bolts. Failure to tighten securely is extremely dangerous.

Installing balance stand (Fig. 8)

When using the balance stand on the tool, be sure not

to block the air vents.

Switch action (Fig. 9)

CAUTION:

Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the ‘‘OFF’’ position when

released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger.

Release the trigger to stop.

Cutting operation (Fig. 10, 11, 12, 13 and 14)

1. Place the steel rod (material to be cut) in the

opening so as to be at right angles to the cutters.

Adjust the stopper (adjusting hex bolt for

SC190DW) in terms of the steel rod size (diam-

eter). When cutting large size steel rods, position

the stopper (adjusting hex bolt) as shown in

Fig. 11-1, 12-1. When cutting small size steel

rods, position the stopper (adjusting hex bolt) as

shown in Fig. 11-2, 12-2. The stopper (adjusting

hex bolt) keeps the steel rod at right angles to the

cutters during the cutting.

2. Keep the steel rod at the deepest position in

between the cutters as shown in Fig. 13-1. Never

keep it as shown in Fig. 13-2. If the steel rod is not

placed at the deepest position between the cut-

ters, it may ride up and cause a fragment or piece

to fly up. Besides this dangerous situation, the

cutters may be damaged. Always position the

steel rod properly.

3. Pull the trigger. The cutter rod advances to cut off

the steel rod. Keep the trigger pulled until the steel

rod is completely cut off.

4. Release the trigger, and the cutter rod will auto-

matically return to its initial position.

NOTE:

The cutter rod will not return to its initial position

even if you release the trigger until the cutter rod

advances all the way and stops. And until the

cutter rod completely return to its initial position, it

will not move forward again even if you pull the

trigger. Pull the trigger to begin the next cut-off

only after the cutter rod has completely returned to

its initial position.

Return valve (Fig. 15)

For SC160DRA and SC190DW

It may happen that the cutters will engage the steel

rod and come to a stop before the cut-off is com-

pleted. In that case, use the hex wrench M4 to release

the hydraulic pressure in the return valve. Insert the

hex wrench M4 into the return valve hole and make a

half turn in the counterclockwise direction. This

releases the hydraulic pressure inside the tool, allow-

ing the cutter rod to return to its initial position. Always

retighten the valve before doing the next cut-off job.

Angling into tight places

For SC160DRA and SC190DW

One useful feature is that you can, even after begin-

ning a cut-off (load condition), rotate the tool by the

handle 360° left or right. This makes work in tight

places easier, especially trigger access and activa-

tion. You can even swing the tool while pulling the

trigger.

SC130DRA/SC160DRA/SC190DW (E) (’100. 1. 13)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita SC 190DW Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita SC 190DW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info