Bedienungsanleitung Makita sp 6000 k 1x (Seite 7 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Norwegisch)

383806

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

Explanation of general view

SPECIFICATIONS

• Due to our continuing programme of research and development, the specifications herein are subject to change without

notice.

• Note: Specifications may differ from country to country.

Intended use

ENE067-1

The tool is specially intended for performing plunge cuts.

In addition, lengthways and crossways straight cuts and

mitre cuts with angles in wood can also be performed

while in firm contact with the workpiece.

If the tool is equipped with the special saw blade for

aluminium, the tool can be used for sawing aluminium.

Power supply

ENF002-1

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

SPECIFIC SAFETY RULES GEB031-1

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to

circular saw safety rules. If you use this tool unsafely

or incorrectly, you can suffer serious personal injury.

Danger:

1. Keep hands away from cutting area and the blade.

Keep your second hand on auxiliary handle, or

motor housing. If both hands are holding the saw,

they cannot be cut by the blade.

2. Do not reach underneath the workpiece or tool

base. The guard cannot protect you from the blade

below the workpiece. Do not attempt to remove cut

material when blade is moving.

CAUTION: Blades coast after turn off. Wait until blade

stops before grasping cut material.

3. Adjust the cutting depth to the thickness of the

workpiece. Less than a full tooth of the blade teeth

should be visible below the workpiece.

4. Never hold piece being cut in your hands or

across your leg. Secure the workpiece to stable

platform. It is important to support the work properly

to minimize body exposure, blade binding, or loss of

control.

A typical illustration of proper hand support,

workpiece support, and supply cord routing (if

applicable). (Fig. 1)

1. Clamping screw

2. Blade lower limit stopper

3. Quick stop button

4. Clamping screws

5. Tool base

6. Positive stopper

7. Lever

8. Bevel angle shifting lever

9. Base

10. Cutting line

11. Lock-off button

12. Switch trigger

13. Speed adjusting dial

14. Hex wrench

15. Locking lever

16. Shaft lock

17. Hex bolt

18. Outer flange

19. Saw blade

20. Inner flange

21. Vacuum cleaner

22. Dust port

23. Adjusting screws

24. Slide lever

25. Rip fence (Guide rule)

26. Rear edge of tool base

27. Fixed stop

28. Adjusting screw for 90°

29. Adjusting screw for 45°

30. Limit mark

31. Screwdriver

32. Brush holder cap

Model SP6000

Blade diameter 165 mm

Max. cutting depth

at 90° 56 mm

at 45° 40 mm

at 48° 38 mm

No load speed (min

-1

) 2,000 - 5,200

Overall length 341 mm

Net weight 4.1 kg

Safety class /II

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita sp 6000 k 1x Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info