Bedienungsanleitung Makita T 221D (Seite 4 von 10) (Englisch, Holländisch)

448656

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

ENGLISH

Explanation of general view

1 Battery cartridge

2 Set plate

3 Trigger

4 Safety lever

5 Plate spring

6 Slide backward

7 Press

8 Staples

9Push

10 Nut

11 Turn

12 tool end (A)

13 Less than 2mm

14 Material

15 Sight window

SPECIFICATIONS

Model T221D

Staple width ...........................................................10 mm

Applicable staples length ............... 10, 13,16, 19, 22mm

Staple magazine capacity ................................. 100 pcs.

Dimensions (Lx W x H) ....................... 199 x 58 x 193 mm

Net weight ..............................................................1.7 kg

Rated voltage ...................................................D.C. 9.6 V

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Intended use

The tool is intended for pressing staples into construction

materials such as timbers.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

IMPORTANT SAFETY INSTRUCTIONS

FOR CHARGER & BATTERY CARTRIDGE

ENC004-1

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Always cover the battery terminals with the bat-

tery cover when the battery cartridge is not

used.

6. Do not short the battery cartridge:

(1) Do not touch the terminals with any conduc-

tive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

7. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

8. Do not incinerate the battery cartridge even if it

is severely damaged or is completely worn out.

The battery cartridge can explode in a fire.

9. Be careful not to drop or strike battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the bat-

tery cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tempera-

ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-

tery cartridge cool down before charging it.

4. Charge the Nickel Metal Hydride battery car-

tridge when you do not use it for more than six

months.

ADDITIONAL SAFETY RULES FOR TOOL

1. Always wear safety goggles or safety glasses

with side shield, and a full face shield when

needed.

2. Do not point the ejection port at anyone in the

vicinity (especially his face). Keep hands and

feet away from the ejection port area.

3. Always remove the battery cartridge before load-

ing the staples, adjustment, inspection, mainte-

nance or after operation is over.

4. Make sure no one is nearby before operation.

Never attempt to drive staples from both the

inside and outside of wall at the same time. Sta-

ples may rip through and/or fly off, presenting a

grave danger.

5. Watch your footing and maintain your balance

with the tool. Make sure there is no one below

when working in high locations.

6. Check walls, ceilings, floors, roofing and the like

carefully to avoid possible electrical shock, gas

leakage, explosions, etc. caused by stapling into

live wires, conduits or gas pipes.

7. Use only staples specified in this manual. The

use of any other staples may cause malfunction

of the tool.

8. Do not tamper with the tool or attempt to use it

for other than driving staples.

9. Do not operate the tool without staples. It short-

ens the service life of the tool.

10. Stop driving operations immediately if you

notice something wrong or out of the ordinary

with the tool.

11. Never staple into any materials which may allow

the staple to puncture and fly through as a pro-

jectile.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita T 221D Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita T 221D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info