Bedienungsanleitung Makita T 221D (Seite 5 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448656

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ADDITIONAL SAFETY RULES

FOR MACHINE

1. Always wear safety goggles or safety glasses

with side shield, and a full face shield when

needed.

2. Do not point the ejection port at anyone in the

vicinity (especially his face). Keep hands and

feet away from the ejection port area.

3. Always remove the battery cartridge before

loading the staples, adjustment, inspection,

maintenance or after operation is over.

4. Make sure no one is nearby before operation.

Never attempt to drive staples from both the

inside and outside of wall at the same time.

Staples may rip through and/or fly off, present-

ing a grave danger.

5. Watch your footing and maintain your balance

with the machine. Make sure there is no one

below when working in high locations.

6. Check walls, ceilings, floors, roofing and the

like carefully to avoid possible electrical

shock, gas leakage, explosions, etc. caused

by stapling into live wires, conduits or gas

pipes.

7. Use only staples specified in this manual. The

use of any other staples may cause malfunc-

tion of the machine.

8. Do not tamper with the machine or attempt to

use it for other than driving staples.

9. Do not operate the machine without staples. It

shortens the service life of the machine.

10. Stop driving operations immediately if you

notice something wrong or out of the ordinary

with the machine.

11. Never staple into any materials which may

allow the staple to puncture and fly through as

a projectile.

12. Never actuate the switch trigger and safety

lever at the same time until you are prepared

to staple workpieces. Allow the workpiece to

depress the safety lever. Never defeat its pur-

pose by securing the safety lever back or by

depressing it by hand.

13. Never tamper with the safety lever. Check the

safety lever frequently for proper operations.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge

(Fig. 1)

•

Always switch off the machine before insertion or

removal of the battery cartridge.

•

To remove the battery cartridge, pull out the set

plate on the machine and grasp both sides of the

cartridge while withdrawing it from the machine.

•

To insert the battery cartridge, align the tongue on

the battery cartridge with the groove in the housing

and slip it into place. Snap the set plate back into

place. Be sure to close the set plate fully before

using the machine.

•

Do not use force when inserting the battery car-

tridge. If the cartridge does not slide in easily, it is

not being inserted correctly.

Charging (Fig. 2)

1. Plug the battery charger into your power source.

2. Insert the battery cartridge so that the plus and

minus terminals on the battery cartridge are on the

same sides as their respective markings on the

battery charger. Insert the cartridge fully into the

port so that it rests on the charger port floor.

3. When the battery cartridge is inserted, the charg-

ing light color will flash in red color and charging

will begin.

4. When charging is completed, the charging light

goes out. The charging time is as follows:

Battery 7000, 7100, 7120, 9000, 9100, 9100A,

9120: approx. 60 minutes.

5. If you leave the battery cartridge in the charger

after the charging cycle is complete, the charger

will switch into its ‘‘trickle charge (maintenance

charge)’’ mode.

6. After charging, remove the battery cartridge from

the charger and unplug the charger from the

power source.

Battery type

Capacity

(mAh)

Number of

cells

9100 1,300 8

CAUTION:

•

The battery charger is for charging Makita battery

cartridge. Never use it for other purposes or for

other manufacturer’s batteries.

•

When you charge a new battery cartridge or a

battery cartridge which has not been used for a long

period of time, it may not accept a full charge. This

is a normal condition and does not indicate a

problem. You can recharge the battery cartridge

fully after discharging it completely and recharging a

couple of times.

•

When you charge a battery cartridge from a just-

operated machine or a battery cartridge which has

been left in a location exposed to direct sunlight or

heat for a long time, let it cool off. Then re-insert it

and try to charge it once more.

•

When you charge a new battery cartridge or a

battery cartridge which has not been used for a long

period, sometimes the charging light will go out

soon. If this occurs, remove the battery cartridge

and re-insert it. If the charging light goes out within

one minute even after repeating this procedure a

couple of times, the battery cartridge is dead.

Replace it with a new one.

Trickle charge (Maintenance charge)

If you leave the battery cartridge in the charger to

prevent spontaneous discharging after full charge,

the charger will switch into its ‘‘trickle charge (main-

tenance charge)’’ mode and keep the battery car-

tridge fresh and fully charged.

T221D (E) (’100. 3. 20)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita T 221D Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita T 221D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info