Bedienungsanleitung Makita TD 0101 (Seite 4 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448657

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ENGLISH

Explanation of general view

SPECIFICATIONS

• Due to our continuing programme of research and development, the specifications herein are subject to change without

notice.

• Note: Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

Intended use

ENE033-1

The tool is intended for screw driving in wood, metal and

plastic.

Power supply

ENF002-1

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

SPECIFIC SAFETY RULES GEB012-3

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to impact

driver safety rules. If you use this tool unsafely or

incorrectly, you can suffer serious personal injury.

1. Hold power tool by insulated gripping surfaces,

when performing an operation where the fastener

may contact hidden wiring or its own cord.

Fasteners contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

2. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

3. Hold the tool firmly.

4. Wear ear protectors.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 1)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

Lighting up the lamp (Model TD0101F

only) (Fig. 2)

CAUTION:

• Do not look in the light or see the source of light

directly.

Connect the plug to light up the lamp. The lamp keeps on

lighting while the plug is connected.

1. Switch trigger

2. Lamp

3. Reversing switch lever

4. Bit

5. Sleeve

6. Bit-piece

7. Standard bolt

8. Fastening torque

9. Fastening time (S)

10. Proper fastening torque

11. High tensile bolt

12. Limit mark

13. Screwdriver

14. Brush holder cap

15. Screw

16. Hook

17. Groove

18. Bumper

19. Hammer case cover

Model TD0101/TD0101F

Capacities

Machine screw 4 mm - 8 mm

Standard bolt 5 mm - 14 mm

High tensile bolt 5 mm - 10 mm

No load speed (min

-1

) 0 - 3,600

Impacts per minute (min

-1

) 0 - 3,200

Max. fastening torque 100 N•m

Dimensions (L x W x H) 184 mm x 67 mm x 192 mm

Net weight 0.99 kg

Safety class /II

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita TD 0101 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info