Bedienungsanleitung Makita td 090 d (Seite 6 von 40) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

381503

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Hold the tool firmly and place the point of the driver bit in

the screw head. Apply forward pressure to the tool to the

extent that the bit will not slip off the screw and turn the

tool on to start operation.

NOTE:

• Use the proper bit for the head of the screw/bolt that

you wish to use.

• When fastening screw M8 or smaller, carefully adjust

pressure on the switch trigger so that the screw is not

damaged.

• Hold the tool pointed straight at the screw.

• If you tighten the screw for a time longer than shown in

the figures, the screw or the point of the driver bit may

be overstressed, stripped, damaged, etc. Before

starting your job, always perform a test operation to

determine the proper fastening time for your screw.

The fastening torque is affected by a wide variety of

factors including the following. After fastening, always

check the torque with a torque wrench.

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening torque

will be reduced.

2. Driver bit or socket bit

Failure to use the correct size driver bit or socket bit

will cause a reduction in the fastening torque.

3. Bolt

• Even though the torque coefficient and the class of

bolt are the same, the proper fastening torque will

differ according to the diameter of bolt.

• Even though the diameters of bolts are the same,

the proper fastening torque will differ according to

the torque coefficient, the class of bolt and the bolt

length.

4. The manner of holding the tool or the material of

driving position to be fastened will affect the torque.

5. Operating the tool at low speed will cause a reduction

in the fastening torque.

Using holster

CAUTION:

• Do not use for tools such as a drill with a bit installed on

them.

• Turn off a tool and wait until it comes to a complete

stop before placing in the holster.

Be sure to close the holster securely so that it holds the

tool firmly.

Thread a waist belt or similar through holster holder.

Put the tool in the holster and lock it with the holster

button. (Fig. 11 & 12)

Two bits can be retained at the front of holster. (Fig. 13)

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Screw bits

• Socket bits

• Bit piece

•Holster

• Plastic carrying case

• Various type of Makita genuine batteries and chargers

For European countries only

Noise

ENG102-1

The typical A-weighted noise level determined according

to EN60745-2-2:

Sound pressure level (L

): 92 dB (A)

Sound power level (L

): 103 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection

Vibration

ENG205-1

The vibration total value (tri-axial vector sum) determined

according to EN60745-2-2:

Work mode : impact tightening of fasteners of the

maximum capacity of the tool

Vibration emission (a

): 10 m/s

Uncertainty (K): 1.5 m/s

EC-DECLARATION OF CONFORMITY ENH102-7

Model; TD090D

We declare under our sole responsibility that this product

is in compliance with the following standards of

standardized documents; EN60745, EN55014 in

accordance with Council Directives, 2004/108/EC,

98/37/EC.

CE 2007

Tomoyasu Kato

Director

Responsible Manufacturer:

Makita Corporation

3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN

Authorized Representative in Europe:

Makita International Europe Ltd.

Michigan Drive, Tongwell, Milton Keynes, Bucks MK15

8JD, ENGLAND

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita td 090 d Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info