Bedienungsanleitung Makita TD111DSAJ (Seite 7 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711189

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

7 ENGLISH

Changing the impact force

►Fig.7: 1. Hard 2. Soft 3.Amode4. Changed in three

steps 5. Button

Youcanchangetheimpactforceinthreesteps:hard,

soft,andAmode.

Thisallowsatighteningsuitabletothework.

Everytimethebuttonispressed,thenumberofblows

changes in three steps.

“Amode(assistmode)”isaneasy-to-usemodefor

driving screws with good control.

In this mode, the tool drives a screw with low-speed

rotationatrst.Afterthetoolstartstoimpact,therota-

tionspeedincreasesandreachesthemaximumspeed.

Forapproximatelyoneminuteafterreleasingtheswitch

trigger, the impact force can be changed.

Impact force grade displayed

on panel

Maximum blows Purpose Example of application

Hard

3,900 min

-1

(/min) Tighteningwhenforceand

speed are desired.

Tighteningwoodscrews,

tightening bolts.

Soft

1,600 min

-1

(/min) Tighteningwithlessforceto

avoid screw thread breakage.

Tighteningsashscrews,tight-

ening small screws such as M6.

Amode

3,900 min

-1

(/min) Tighteningscrewswithbetter

control.

Tighteninglongscrews.

NOTE:Amodeisavailableonlywhenthetoolrotatesclockwise.WhenrotatingcounterclockwiseinAmode,the

impact force and speed are the same as hard mode.

NOTE:Whenalllampsontheswitchpanelgoout,thetoolisturnedofftosavethebatterypower.Theimpactforce

gradecanbecheckedbypullingtheswitchtriggertotheextentthatthetooldoesnotoperate.

NOTE:Whilepullingtheswitchtrigger,theimpactforcegradecannotbechanged.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/

socket bit

Optional accessory

►Fig.8

Useonlydriverbit/socketbitthathasinsertingportionshown

inthegure.Donotuseanyotherdriverbit/socketbit.

For tool with shallow driver bit hole

A=12mm

B=9mm

Use only these type of driver

bit. Follow the procedure

1. (Note) Bit-piece is not

necessary.

For tool with deep driver bit hole

A=17mm

B=14mm

Toinstallthesetypesofdriver

bits, follow the procedure 1.

A=12mm

B=9mm

Toinstallthesetypesofdriver

bits, follow the procedure 2.

(Note) Bit-piece is necessary

for installing the bit.

1. Toinstallthedriverbit,pullthesleeveinthedirec-

tion of the arrow and insert the driver bit into the

sleeve as far as it will go.

Thenreleasethesleevetosecurethedriverbit.

►Fig.9: 1. Driver bit 2. Sleeve

2. Toinstallthedriverbit,pullthesleeveinthedirec-

tion of the arrow and insert the bit-piece and driver

bitintothesleeveasfarasitwillgo.Thebit-piece

should be inserted into the sleeve with its pointed

endfacingin.Thenreleasethesleevetosecure

the driver bit.

►Fig.10: 1. Driver bit 2. Bit-piece 3. Sleeve

Toremovethedriverbit,pullthesleeveinthedirection

of the arrow and pull the driver bit out.

NOTE: If the driver bit is not inserted deep enough

into the sleeve, the sleeve will not return to its original

position and the driver bit will not be secured. In this

case, try re-inserting the bit according to the instruc-

tions above.

NOTE:Afterinsertingthedriverbit,makesurethatit

isrmlysecured.Ifitcomesout,donotuseit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita TD111DSAJ Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info