Bedienungsanleitung Makita TM3000C (Seite 6 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598927

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

19. Be sure that there are no cracks or breakage on

the pad before use. Cracks or breakage may

cause a personal injury.

20. Do not use accessories which are not specifi-

cally designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

21. Wear personal protective equipment. Depend-

ing on application, use face shield, safety gog-

gles or safety glasses. As appropriate, wear

hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece

fragments. The eye protection must be capable of

stopping flying debris generated by various opera-

tions. The dust mask or respirator must be capable

of filtrating particles generated by your operation.

Prolonged exposure to high intensity noise may

cause hearing loss.

22. Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may fly away

and cause injury beyond immediate area of opera-

tion.

23. Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

accessory may grab the surface and pull the power

tool out of your control.

24. Do not run the power tool while carrying it at

your side. Accidental contact with the accessory

could snag your clothing, pulling the accessory into

your body.

25. Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

26. Do not use accessories that require liquid cool-

ants. Using water or other liquid coolants may result

in electrocution or shock.

27. Always be sure that the tool is switched off and

unplugged before carrying out any work on the

tool.

28. If working place is extremely hot and humid, or

badly polluted by conductive dust, use a short-

circuit breaker (30 mA) to assure operator safety.

29. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high loca-

tions.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this instruc-

tion manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

WARNING:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function

on the tool. Failure to switch off and unplug the tool

may result in serious personal injury from accidental

start-up.

Switch action (Fig. 1)

CAUTION:

• Before plugging in the tool, always check to see that

the tool is switched off.

To start the tool, slide the slide switch toward the “I (ON)”

position.

To stop the tool, slide the slide switch toward the “O

(OFF)” position.

Adjusting the orbital stroke rate (Fig. 2)

The orbital stroke rate is adjustable. To change the orbital

stroke rate, turn the dial between 1 and 5. The higher the

number is, the higher the orbital stroke rate is. Preset the

dial to the number suitable for your workpiece.

NOTE:

• The dial cannot be turned directly from 1 to 5 or from 5

to 1. Forcing the dial may damage the tool. When

changing the dial direction, always turn the dial moving

it through each intermediate number.

Constant speed control

Electronic speed control for obtaining constant speed.

Possible to get fine finish, because the orbital stroke rate

is kept constant even under load condition.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing application tool (optional

accessory) (Fig. 3, 4 & 5)

WARNING:

• Do not install application tool upside down. Installing

application tool upside down may damage the tool and

cause serious personal injury.

• Install attachment tool in the correct direction according

to your work. Application tool can be installed at an

angle of every 30 degree.

Put an application tool (optional accessory) on the tool

flange so that the protrusions of the tool flange fit in the

holes in the application tool and secure the application

tool by tightening the bolt firmly with the hex wrench.

When using sanding application tool, mount the applica-

tion tool on the sanding pad so that it matches the sand-

ing pad direction.

The sanding pad has a hook and loop type fitting system

which allows easy and rapid fitting of a sanding paper.

As sanding papers have holes for dust extraction, mount

a sanding paper so that the holes in a sanding paper

match those in the sanding pad.

To remove a sanding paper, raise its end and peel it off.

Loosen and remove the application tool installation bolt

using a hex wrench and then take off the application tool.

When using application tools with a different type of

installation section, use a correct adapter (optional

accessory).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita TM3000C Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info