Bedienungsanleitung Makita TM3010CX2J (Seite 7 von 14) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711184

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

OPERATION

WARNING:

• Before starting the tool and during operation, keep your

hand and face away from the application tool.

CAUTION:

• Always hold the tool firmly with one hand on housing.

Do not touch the metal part.

• Do not apply excessive load to the tool which may

cause a motor lock and stop the tool.

Cutting, sawing and scraping (Fig. 7)

CAUTION:

• Do not move on the tool forcibly in the direction (e.g.

towards either side) of tool application with no cutting

edge. It may damage the tool.

Put the application tool on the workpiece.

And then move the tool forward so that the application

tool movement does not slow down.

NOTE:

• Forcing or excessive pressure on the tool may reduce

efficiency.

• Remove sawdust by drawing tool adequately. It

increases work efficiency.

• Before cutting operation, it is recommended to preset

the orbital stroke rate 3 – 5.

• The round saw is recommended for cutting long

straight line.

Sanding (Fig. 8)

CAUTION:

• Do not reuse a sanding paper used for sanding metal

to sand wood.

• Do not use a worn sanding paper or sanding paper

without grit.

Apply a sanding paper on the workpiece.

NOTE:

• Using a test material sample to try is recommendable

to determine a correct orbital stroke rate suitable for

your work.

• Use a sanding paper with the same grit until sanding

the whole workpiece is completed. Replacing a

sanding paper with different grit sanding paper may not

get a fine finish.

Dust extraction attachment (optional accessory)

(Fig. 9, 10 & 11)

• Install joint, dust nozzle and dust attachment.

• Install the nozzle band on the tool so that its

protrusions fit in the holes in the tool to secure it.

• Put the felt ring and the sanding pad on the dust

attachment and then secure them with the application

tool installation bolt.

When you wish to perform cleaner operation, connect a

vacuum cleaner to your tool. Connect a hose of vacuum

cleaner to the dust extraction attachment (optional

accessory).

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Segment saw blade

• Round saw blade

• Plunge cut saw blade

• Scraper (rigid)

• Scraper (flexible)

• Serrated seg blade

• General joint cutter

• HM remover

• HM seg saw blade

• HM sanding plate

• Diamond seg sawblade

• Sanding pad

• Adapter

• Abrasive paper delta (red / white / black)

• Fleece delta (medium / coarse / without grit)

• Polishing felt delta

• Hex wrench

• Dust extraction attachment

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ from

country to country.

ENG905-1

Noise

The typical A-weighted noise level determined according

to EN60745:

Work mode: sanding

Sound pressure level (L

): 80 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Work mode: cutting with plunge cut saw blade

Sound pressure level (L

): 80 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Work mode: cutting with segment saw blade

Sound pressure level (L

): 79 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Work mode: scraping

Sound pressure level (L

): 82 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita TM3010CX2J Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info