Bedienungsanleitung Makita TW161D (Seite 6 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691726

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

6 ENGLISH

Tips for maintaining maximum

battery life

Charge the battery cartridge before completely dis-

charged. Always stop tool operation and charge the

battery cartridge when you notice less tool power.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge.Failuretoholdthetoolandthebattery

cartridgermlymaycausethemtoslipoffyourhands

andresultindamagetothetoolandbatterycartridge

andapersonalinjury.

►Fig.1: 1. Red indicator 2. Button 3.Batterycartridge

Toremovethebatterycartridge,slideitfromthetool

while sliding the button on the front of the cartridge.

Toinstallthebatterycartridge,alignthetongueonthe

batterycartridgewiththegrooveinthehousingandslip

itintoplace.Insertitallthewayuntilitlocksinplace

withalittleclick.Ifyoucanseetheredindicatoronthe

uppersideofthebutton,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

youorsomeonearoundyou.

CAUTION: Do not install the battery cartridge

forcibly.Ifthecartridgedoesnotslideineasily,itis

notbeinginsertedcorrectly.

Battery protection system

Thetoolisequippedwithabatteryprotectionsystem.

Thissystemautomaticallycutsoffpowertothemotorto

extendbatterylife.

Thetoolwillautomaticallystopduringoperationifthe

tooland/orbatteryareplacedunderoneofthefollowing

conditions:

Overloaded:

The tool is operated in a manner that causes it to draw

anabnormallyhighcurrent.

In this situation, turn the tool off and stop the application

that caused the tool to become overloaded. Then turn

the tool on to restart.

Ifthetooldoesnotstart,thebatteryisoverheated.Inthis

situation,letthebatterycoolbeforeturningthetoolonagain.

Low battery voltage:

Theremainingbatterycapacityistoolowandthetool

willnotoperate.Ifyouturnthetoolon,themotorruns

again but stops soon. In this situation, remove and

rechargethebattery.

Indicating the remaining battery capacity

Only for battery cartridges with the indicator

►Fig.2: 1. Indicator lamps 2. Check button

Pressthecheckbuttononthebatterycartridgetoindi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted Off

75% to 100%

50% to 75%

25% to 50%

0% to 25%

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydifferslightly

fromtheactualcapacity.

Switch action

►Fig.3: 1. Switch trigger

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

Tostartthetool,simplypulltheswitchtrigger.Tool

speedisincreasedbyincreasingpressureontheswitch

trigger. Release the switch trigger to stop.

NOTE:Thetoolautomaticallystopsifyoukeeppull-

ing the switch trigger for about 6 minutes.

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

►Fig.4: 1. Lamp

►Fig.5: 1. Button

Pull the switch trigger to turn on the lamp. To turn off,

releaseit.Thelampgoesoutapproximately10seconds

after releasing the switch trigger.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita TW161D Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info